- Location
- Kirkwall, Orkney, Shetland and the Western Isles
- Main postcode district
- KW15
- Nearby (straight line)
- Remote location, covered by arrangement
- Survey and quote
- Free, with a fixed written quote
Dock lights and wheel guides are two simple loading bay aids. A dock light is a lamp, usually LED, on a swing arm beside the dock door that shines into the trailer so forklift drivers can see the load. Wheel guides are steel rails fixed to the yard that steer the rear wheels so the trailer arrives straight and centred on the leveller.
Why do sites in Kirkwall choose this?
Any site in Kirkwall considering these items gets the same survey and fixed written quote that we provide across England, Scotland, Wales and Northern Ireland. A landlord preparing a unit in Kirkwall for re-letting can add dock lights and wheel guides at modest cost to make the bays more practical.
On older estates around Kirkwall, dock lights may still use outdated lamps, and an LED swing-arm light is a simple upgrade that runs cooler.
Step one is a survey at your site in Kirkwall, which costs nothing and carries no obligation. Step two is a written quote with a fixed price and a clear scope. Step three is installation, scheduled around your operation and carried out by specialist installation engineers working under our management, including evenings or weekends if agreed. Step four is handover, when the equipment is tested in front of you and the paperwork is passed over.
Which type of dock light is best for a loading bay?
An LED swing-arm dock light is the usual choice for a loading bay, because it reaches into the trailer during loading and folds back flat against the wall when the bay is closed. LED heads run much cooler than older lamps and cope better with knocks and vibration.
- Arm length: longer arms push light further into deep trailers, but need clear wall space so they can fold away from the door path.
- Rigid or flexible arm: a rigid arm with a pivoting head is tougher; a flexible section can be easier to aim.
- Guarding: a protective cage or polycarbonate cover helps the head survive forklift contact.
- Switching: a switch on the head or on the wall, or linked to the door so the light comes on as it opens.
- Supply voltage: mains or low-voltage, confirmed at survey to suit your site.
The light is mounted inside the building beside the door, clear of the door tracks, at a height that lets it swing over the leveller and into the trailer.
Should wheel guides be bolted down or cast in?
Wheel guides are bolted down on an existing sound concrete yard and cast in where new concrete is being laid. Both give a strong fixing; the choice depends on whether the yard is being resurfaced.
- Bolt-down guides: steel tube or channel fixed with resin anchors. Quick to fit to existing bays and easy to replace if damaged.
- Cast-in guides: set into fresh concrete with embedded anchors, suited to new-build docks and conversions.
- Flared entry: an angled lead-in at the yard end catches the wheel early and steers it into line.
- Finish: typically galvanised, or painted yellow and black so drivers can see them in mirrors.
Guides are set out to suit the track width of the trailers you receive, centred on the leveller, and long enough to straighten the trailer before it reaches the bumpers. Tarmac is usually too soft to hold anchors, so a concrete strip or base is laid first. Our guide to choosing dock bumpers and wheel guides covers layout in more depth.
The same published guide range applies across Scotland; access, out-of-hours working and site conditions are confirmed at the free survey.
What do we check at the survey?
- Headroom above the opening and which track type will suit it
- Scope to convert ground-level doors into docks or add lift tables
- Wheel guide positions and yard markings for reversing vehicles
- Access for deliveries, cranes or lifting equipment during installation
- Escape routes and pedestrian doors close to the bay
- Wind exposure at the dock, which affects door and shelter choice
Options to discuss
Low-voltage dock light
A swing-arm light fed through a transformer mounted nearby, for sites that prefer a reduced voltage at the lamp head. Same reach and folding action as a mains light.
Cast-in wheel guides
Guides set into new concrete with embedded anchors during yard works, giving a very strong fixing for new-build docks, resurfaced yards and loading bay conversions.
Regulations and approvals in Scotland
Doors and dock equipment installed in Scotland may carry the UKCA or the CE mark, and we pass on the documentation for everything fitted in Kirkwall. Because building warrant and planning questions can affect the programme, we check what applies at survey and raise any approvals early rather than assuming none are needed.
Sites in and around Kirkwall are covered by arrangement. There is no charge for the survey or the written quote, and any travel, ferry crossings or overnight stays needed for the installation itself are itemised in the quote, so you see the full price before agreeing.
Questions about dock lights and wheel guides in Kirkwall
How do you price dock lights and wheel guides for a site in Kirkwall?
Guide budgets for supply and fit are £280 to £950 per item, excluding VAT. The figure moves with size, insulation, the operator, electrics, access, any pit or groundworks and out-of-hours working. Where levellers are involved, the guide assumes an existing, sound pit. After the free survey you receive a fixed written quote, and that is the price for the agreed scope.
Do you cover Kirkwall for dock lights and wheel guides?
Yes. We take on dock lights and wheel guides for businesses in Kirkwall and across Orkney, Shetland and the Western Isles. We survey the site, provide a fixed written quote and manage the installation, with specialist installation engineers working under our management. Visits are arranged in advance at a time that suits your operation, and the same single contact stays with the job through to handover.
Can you work alongside our main contractor on a new build in Kirkwall?
Yes. For new warehouses and fit-outs, we can supply and install the dock package as part of a wider project, working to the main contractor's programme, site rules and permits. We will need drawings, dock levels and the programme, and we coordinate pit details, power supplies and door openings with the relevant trades before installation begins.
Can wheel guides be fitted to a tarmac yard?
Wheel guides can be fitted to a tarmac yard, but tarmac is usually too soft to hold anchors on its own. The normal approach is to cut out a strip and lay a concrete base for the guides. That work is identified at survey and included in the written quote.
Where should a dock light be mounted?
A dock light is mounted inside the building beside the door opening, high enough to swing over the leveller and into the trailer. It must fold back flat against the wall, clear of the door tracks and the forklift route, so it is not struck when the bay is not in use.
Dock lights and wheel guides near Kirkwall
Other loading bay services in Kirkwall
Full guide to dock lights and wheel guides · Everything we do in Kirkwall
Speak to us about your Kirkwall loading bay. We will ask the right questions, then set out the next step clearly.