- Location
- Hyde, Greater Manchester
- Main postcode district
- SK14
- Nearby (straight line)
- Ashton-under-Lyne (3 miles), Stockport (4 miles) and Glossop (5 miles)
- Survey and quote
- Free, with a fixed written quote
Dock lights and wheel guides are two simple loading bay aids. A dock light is a lamp, usually LED, on a swing arm beside the dock door that shines into the trailer so forklift drivers can see the load. Wheel guides are steel rails fixed to the yard that steer the rear wheels so the trailer arrives straight and centred on the leveller.
Is this right for your site in Hyde?
A landlord preparing a unit in Hyde for re-letting can add dock lights and wheel guides at modest cost to make the bays more practical. Warehouses in Hyde loading deep trailers by forklift often find the back of the load hard to see without a dock light reaching into the trailer.
Tight yards in Hyde where drivers reverse between parked trailers or around buildings make wheel guides especially useful for getting the trailer straight first time.
If you are planning dock lights and wheel guides for a site in Hyde, expect four stages. A free survey and fixed written quote come first. We then agree a programme with you, including any out-of-hours work. Specialist installation engineers carry out the installation under our management, with us as your single point of contact. Finally, the equipment is tested, your staff are shown how it works and everything is handed over with its documentation.
Which type of dock light is best for a loading bay?
An LED swing-arm dock light is the usual choice for a loading bay, because it reaches into the trailer during loading and folds back flat against the wall when the bay is closed. LED heads run much cooler than older lamps and cope better with knocks and vibration.
- Arm length: longer arms push light further into deep trailers, but need clear wall space so they can fold away from the door path.
- Rigid or flexible arm: a rigid arm with a pivoting head is tougher; a flexible section can be easier to aim.
- Guarding: a protective cage or polycarbonate cover helps the head survive forklift contact.
- Switching: a switch on the head or on the wall, or linked to the door so the light comes on as it opens.
- Supply voltage: mains or low-voltage, confirmed at survey to suit your site.
The light is mounted inside the building beside the door, clear of the door tracks, at a height that lets it swing over the leveller and into the trailer.
Do health and safety rules cover dock lights and wheel guides?
Dock lights and wheel guides support your wider loading bay safety duties rather than replacing them. Once fitted, a dock light is work equipment under the Provision and Use of Work Equipment Regulations 1998 (PUWER), so it must be suitable, maintained in a safe condition and inspected where deterioration could lead to danger. In Northern Ireland the equivalent is PUWER (Northern Ireland) 1999.
HSE's guide to workplace transport safety (HSG136) is the main reference for managing vehicles in the yard, and its loading guidance says there should be safeguards against drivers driving away too early, such as traffic lights, restraints or key control. Wheel guides and dock lights do not meet that requirement on their own, but they help drivers park accurately and help dock staff see what they are doing.
Electrical work for dock lights is carried out by qualified electricians and tested before use. The regulator is HSE in Great Britain and HSENI in Northern Ireland.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What we look at on site
- Wheel guide positions and yard markings for reversing vehicles
- Bumper position and wear or damage on the dock face
- Escape routes and pedestrian doors close to the bay
- Scope to convert ground-level doors into docks or add lift tables
- Yard gradient and the slope of the approach to the dock
- How drivers are prevented from pulling away too early
Options to discuss
Cast-in wheel guides
Guides set into new concrete with embedded anchors during yard works, giving a very strong fixing for new-build docks, resurfaced yards and loading bay conversions.
LED swing-arm dock light
An LED head on a swing arm beside the door, swung into the trailer during loading and folded back flat against the wall when the bay is closed.
Regulations and approvals in England
Powered doors and dock equipment installed in England may carry the UKCA or the CE mark, and doors are covered by the product standard BS EN 13241. We hand over the relevant documentation for each item fitted in Hyde. Planning and Building Regulations questions are never assumed either way: we check what applies at survey, so you know before work is booked.
Questions about dock lights and wheel guides in Hyde
What details do you need from us to quote for dock lights and wheel guides?
To get started, send the site address in Hyde, the number of bays or openings, approximate sizes, and photos of the dock from inside and outside. Tell us what vehicles you load, what goods you handle and any temperature requirements. Drawings help on new builds. We then arrange the free survey and confirm the details before the written quote is issued.
Can you work outside our normal operating hours in Hyde?
Yes, by arrangement. Evening, night and weekend working can be planned so the installation causes as little disruption as possible to your loading schedule. Out-of-hours work can affect the price, so mention it at the survey and we will include it in the written quote. The agreed times are confirmed in the programme before the job starts.
How do you price dock lights and wheel guides for a site in Hyde?
Guide budgets for supply and fit are £280 to £950 per item, excluding VAT. The figure moves with size, insulation, the operator, electrics, access, any pit or groundworks and out-of-hours working. Where levellers are involved, the guide assumes an existing, sound pit. After the free survey you receive a fixed written quote, and that is the price for the agreed scope.
Can wheel guides be fitted to a tarmac yard?
Wheel guides can be fitted to a tarmac yard, but tarmac is usually too soft to hold anchors on its own. The normal approach is to cut out a strip and lay a concrete base for the guides. That work is identified at survey and included in the written quote.
Do wheel guides damage tyres?
Correctly spaced wheel guides should not damage tyres. They are set slightly wider than the trailer track so the tyre only brushes the guide when the trailer is off line, and a flared entry stops tyres hitting the end. Guides that are bent or set too narrow should be corrected.
Dock lights and wheel guides near Hyde
The same survey, quote and repair service is available in towns around Hyde, such as Ashton-under-Lyne (3 miles), Stockport (4 miles) and Glossop (5 miles).
Other loading bay services in Hyde
Full guide to dock lights and wheel guides · Everything we do in Hyde
Phone us to discuss your loading bay in Hyde, or start with the online quote tool if you prefer to send details first.