- Location
- Barking, Greater London
- Main postcode district
- IG11
- Nearby (straight line)
- Beckton (2 miles), Ilford (2 miles) and Thamesmead (3 miles)
- Survey and quote
- Free, with a fixed written quote
Dock lights and wheel guides are two simple loading bay aids. A dock light is a lamp, usually LED, on a swing arm beside the dock door that shines into the trailer so forklift drivers can see the load. Wheel guides are steel rails fixed to the yard that steer the rear wheels so the trailer arrives straight and centred on the leveller.
Is this right for your site in Barking?
Tight yards in Barking where drivers reverse between parked trailers or around buildings make wheel guides especially useful for getting the trailer straight first time. On older estates around Barking, dock lights may still use outdated lamps, and an LED swing-arm light is a simple upgrade that runs cooler.
Shelters and seals at sites near Barking last longer when wheel guides keep trailers centred, because off-centre parking is a common cause of torn curtains.
Your loading bay stays our responsibility from the survey to the handover. In Barking, the survey and written quote are free, and the quoted price is fixed for the agreed scope. Installation is carried out by specialist engineers working under our management, at times planned with you to protect your loading schedule. Out-of-hours work is available by arrangement. We finish by testing the equipment and handing over its documentation.
How do wheel guides protect shelters, seals and levellers?
Wheel guides protect dock equipment by keeping every trailer centred on the bay, so contact forces land where the equipment is designed to take them. A trailer that parks off-centre loads one side of the dock much harder than the other.
- Shelters: off-centre trailers catch the side curtains and frame, causing tears and bent arms.
- Seals: one pad is crushed while the other barely touches, leaving gaps for draughts and rain.
- Levellers: the lip can land near the edge of the trailer bed, with less support for forklifts.
- Bumpers: one bumper takes every impact and wears out early.
Dock lights help in a different way: forklift drivers who can see clearly inside the trailer are less likely to strike the trailer walls or the door frame on the way out. Combining guides and lights with correctly positioned dock bumpers gives a well-protected bay.
Should wheel guides be bolted down or cast in?
Wheel guides are bolted down on an existing sound concrete yard and cast in where new concrete is being laid. Both give a strong fixing; the choice depends on whether the yard is being resurfaced.
- Bolt-down guides: steel tube or channel fixed with resin anchors. Quick to fit to existing bays and easy to replace if damaged.
- Cast-in guides: set into fresh concrete with embedded anchors, suited to new-build docks and conversions.
- Flared entry: an angled lead-in at the yard end catches the wheel early and steers it into line.
- Finish: typically galvanised, or painted yellow and black so drivers can see them in mirrors.
Guides are set out to suit the track width of the trailers you receive, centred on the leveller, and long enough to straighten the trailer before it reaches the bumpers. Tarmac is usually too soft to hold anchors, so a concrete strip or base is laid first. Our guide to choosing dock bumpers and wheel guides covers layout in more depth.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What does the free survey cover?
- How often each door cycles during a typical shift
- Age and condition of the equipment already in place
- Access for deliveries, cranes or lifting equipment during installation
- Yard gradient and the slope of the approach to the dock
- Condition of any existing leveller pit, kerb angles and pit drainage
- Dock height and the mix of trailers you load
Options to discuss
Low-voltage dock light
A swing-arm light fed through a transformer mounted nearby, for sites that prefer a reduced voltage at the lamp head. Same reach and folding action as a mains light.
Cast-in wheel guides
Guides set into new concrete with embedded anchors during yard works, giving a very strong fixing for new-build docks, resurfaced yards and loading bay conversions.
Which rules apply in England?
Powered doors and dock equipment installed in England may carry the UKCA or the CE mark, and doors are covered by the product standard BS EN 13241. We hand over the relevant documentation for each item fitted in Barking. Planning and Building Regulations questions are never assumed either way: we check what applies at survey, so you know before work is booked.
Questions about dock lights and wheel guides in Barking
Is VAT included in your guide prices for dock lights and wheel guides?
No. Our customers are businesses, so guide prices exclude VAT, which is added at the standard rate. The same guide range applies in Greater London as everywhere else: for dock lights and wheel guides, it is £280 to £950 per item, excluding VAT. It covers supply and fit for a typical installation. Your fixed written quote after the free survey shows the net price, the VAT and exactly what is included.
How long does installation take at a site in Barking?
It depends on the equipment, the number of bays, the condition of the dock and whether any building or electrical work is needed. We agree a programme with you after the survey, setting out which bays are out of use and when. Larger jobs are usually phased so that part of the dock stays open, and out-of-hours working can be arranged.
Will you deal with building control and planning for a project in Barking?
We check at survey whether the work is likely to need approval. Forming a new opening or dock pit may need Building Regulations approval, a building warrant or building control approval, depending on the nation, and external structures such as loading houses can need planning permission. Where approval is needed, we explain what is involved, work with your designer or agent, and build it into the programme.
Can dock lights be fitted without stopping loading?
Usually yes. Dock lights are fitted from inside the building beside the door, and the bay can often keep working except for a short period while the supply is isolated and connected. We agree timings with you so the work fits around trailer arrivals.
Can wheel guides be fitted to a tarmac yard?
Wheel guides can be fitted to a tarmac yard, but tarmac is usually too soft to hold anchors on its own. The normal approach is to cut out a strip and lay a concrete base for the guides. That work is identified at survey and included in the written quote.
Dock lights and wheel guides near Barking
Businesses outside Barking may find their nearest town in this list: Beckton (2 miles), Ilford (2 miles) and Thamesmead (3 miles). Each page covers doors, docks, repairs and servicing.
Other loading bay services in Barking
Full guide to dock lights and wheel guides · Everything we do in Barking
Send a few photos of the dock and a short description of the problem, and we will come back to you about your Barking site.