- Location
- Brixham, Devon
- Main postcode district
- TQ5
- Nearby (straight line)
- Paignton (4 miles), Torquay (5 miles) and Newton Abbot (10 miles)
- Survey and quote
- Free, with a fixed written quote
Dock lights and wheel guides are two simple loading bay aids. A dock light is a lamp, usually LED, on a swing arm beside the dock door that shines into the trailer so forklift drivers can see the load. Wheel guides are steel rails fixed to the yard that steer the rear wheels so the trailer arrives straight and centred on the leveller.
Where does this fit at a dock in Brixham?
Resurfacing works on a yard in Brixham are an ideal moment to fit cast-in wheel guides, before the concrete is finished and bays come back into use. A landlord preparing a unit in Brixham for re-letting can add dock lights and wheel guides at modest cost to make the bays more practical.
On older estates around Brixham, dock lights may still use outdated lamps, and an LED swing-arm light is a simple upgrade that runs cooler.
Here is what happens after you contact us about a site in Brixham. We arrange a free survey, measure up and send a fixed written quote. If you go ahead, we manage the whole job, including ordering, delivery and coordination with your site team. Specialist installation engineers working under our management do the fitting, at times built around your loading schedule, with out-of-hours work by arrangement. Testing and handover documents close the job.
Which type of dock light is best for a loading bay?
An LED swing-arm dock light is the usual choice for a loading bay, because it reaches into the trailer during loading and folds back flat against the wall when the bay is closed. LED heads run much cooler than older lamps and cope better with knocks and vibration.
- Arm length: longer arms push light further into deep trailers, but need clear wall space so they can fold away from the door path.
- Rigid or flexible arm: a rigid arm with a pivoting head is tougher; a flexible section can be easier to aim.
- Guarding: a protective cage or polycarbonate cover helps the head survive forklift contact.
- Switching: a switch on the head or on the wall, or linked to the door so the light comes on as it opens.
- Supply voltage: mains or low-voltage, confirmed at survey to suit your site.
The light is mounted inside the building beside the door, clear of the door tracks, at a height that lets it swing over the leveller and into the trailer.
Should wheel guides be bolted down or cast in?
Wheel guides are bolted down on an existing sound concrete yard and cast in where new concrete is being laid. Both give a strong fixing; the choice depends on whether the yard is being resurfaced.
- Bolt-down guides: steel tube or channel fixed with resin anchors. Quick to fit to existing bays and easy to replace if damaged.
- Cast-in guides: set into fresh concrete with embedded anchors, suited to new-build docks and conversions.
- Flared entry: an angled lead-in at the yard end catches the wheel early and steers it into line.
- Finish: typically galvanised, or painted yellow and black so drivers can see them in mirrors.
Guides are set out to suit the track width of the trailers you receive, centred on the leveller, and long enough to straighten the trailer before it reaches the bumpers. Tarmac is usually too soft to hold anchors, so a concrete strip or base is laid first. Our guide to choosing dock bumpers and wheel guides covers layout in more depth.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What do we check at the survey?
- Gaps around trailers where heated or chilled air escapes
- Escape routes and pedestrian doors close to the bay
- Whether planning, building control or a building warrant may be needed
- Yard gradient and the slope of the approach to the dock
- How drivers are prevented from pulling away too early
- Temperature requirements for chilled, frozen or ambient goods
Options to discuss
Low-voltage dock light
A swing-arm light fed through a transformer mounted nearby, for sites that prefer a reduced voltage at the lamp head. Same reach and folding action as a mains light.
Cast-in wheel guides
Guides set into new concrete with embedded anchors during yard works, giving a very strong fixing for new-build docks, resurfaced yards and loading bay conversions.
Regulations and approvals in England
Powered doors and dock equipment installed in England may carry the UKCA or the CE mark, and doors are covered by the product standard BS EN 13241. We hand over the relevant documentation for each item fitted in Brixham. Planning and Building Regulations questions are never assumed either way: we check what applies at survey, so you know before work is booked.
Questions about dock lights and wheel guides in Brixham
Is the site survey in Brixham free?
Yes. For new installations, replacements, upgrades, conversions and complete bays, the site survey and written quote are free and come with no obligation. The survey lets us measure the openings, check the dock and structure, and understand how the bay is used, so the quote reflects your site. Repair and servicing visits are different: they are chargeable, with the price agreed before anyone attends.
Can you work outside our normal operating hours in Brixham?
Yes, by arrangement. Evening, night and weekend working can be planned so the installation causes as little disruption as possible to your loading schedule. Out-of-hours work can affect the price, so mention it at the survey and we will include it in the written quote. The agreed times are confirmed in the programme before the job starts.
Can you work alongside our main contractor on a new build in Brixham?
Yes. For new warehouses and fit-outs, we can supply and install the dock package as part of a wider project, working to the main contractor's programme, site rules and permits. We will need drawings, dock levels and the programme, and we coordinate pit details, power supplies and door openings with the relevant trades before installation begins.
How long should wheel guides be?
Wheel guides need to be long enough to straighten the trailer before it reaches the bumpers, and the right length depends on your yard and approach. Tight yards where drivers turn late usually need longer guides with a flared entry. We set the length and spacing at survey.
Where should a dock light be mounted?
A dock light is mounted inside the building beside the door opening, high enough to swing over the leveller and into the trailer. It must fold back flat against the wall, clear of the door tracks and the forklift route, so it is not struck when the bay is not in use.
Dock lights and wheel guides near Brixham
If your site is not in Brixham itself, it may be near one of these: Paignton (4 miles), Torquay (5 miles) and Newton Abbot (10 miles). Pick the closest.
Other loading bay services in Brixham
Full guide to dock lights and wheel guides · Everything we do in Brixham
Get in touch about loading bay doors and dock equipment in Brixham: call, email or use the quote tool.