- Location
- Whitehaven, Cumbria
- Main postcode district
- CA28
- Nearby (straight line)
- Workington (7 miles)
- Survey and quote
- Free, with a fixed written quote
Dock lights and wheel guides are two simple loading bay aids. A dock light is a lamp, usually LED, on a swing arm beside the dock door that shines into the trailer so forklift drivers can see the load. Wheel guides are steel rails fixed to the yard that steer the rear wheels so the trailer arrives straight and centred on the leveller.
Where does this fit at a dock in Whitehaven?
A landlord preparing a unit in Whitehaven for re-letting can add dock lights and wheel guides at modest cost to make the bays more practical. Resurfacing works on a yard in Whitehaven are an ideal moment to fit cast-in wheel guides, before the concrete is finished and bays come back into use.
On older estates around Whitehaven, dock lights may still use outdated lamps, and an LED swing-arm light is a simple upgrade that runs cooler.
Your loading bay stays our responsibility from the survey to the handover. In Whitehaven, the survey and written quote are free, and the quoted price is fixed for the agreed scope. Installation is carried out by specialist engineers working under our management, at times planned with you to protect your loading schedule. Out-of-hours work is available by arrangement. We finish by testing the equipment and handing over its documentation.
How do wheel guides protect shelters, seals and levellers?
Wheel guides protect dock equipment by keeping every trailer centred on the bay, so contact forces land where the equipment is designed to take them. A trailer that parks off-centre loads one side of the dock much harder than the other.
- Shelters: off-centre trailers catch the side curtains and frame, causing tears and bent arms.
- Seals: one pad is crushed while the other barely touches, leaving gaps for draughts and rain.
- Levellers: the lip can land near the edge of the trailer bed, with less support for forklifts.
- Bumpers: one bumper takes every impact and wears out early.
Dock lights help in a different way: forklift drivers who can see clearly inside the trailer are less likely to strike the trailer walls or the door frame on the way out. Combining guides and lights with correctly positioned dock bumpers gives a well-protected bay.
What happens on site when dock lights or wheel guides are fitted?
Dock lights are fitted from inside the building and usually leave the bay usable for most of the work, while wheel guides close the bay to vehicles until the anchors have cured.
- Dock lights: the bracket is fixed beside the door, the arm and head fitted, and the supply connected and tested. The circuit is isolated briefly during connection.
- Wheel guides: the yard in front of the bay is coned off, guides are set out, drilled and anchored, and the resin is left to cure before trailers return.
- Concrete bases: where tarmac needs a concrete strip first, the bay stays closed until the concrete has gained enough strength.
We ask you to provide a clear bay, details of the nearest power supply, safe yard access and someone who can manage vehicle movements around the work area. Planning guide installation for a quieter period keeps disruption to a minimum.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What we look at on site
- Whether planning, building control or a building warrant may be needed
- Drainage on recessed or sloping dock approaches
- Condition of any existing leveller pit, kerb angles and pit drainage
- Headroom above the opening and which track type will suit it
- Access for deliveries, cranes or lifting equipment during installation
- Escape routes and pedestrian doors close to the bay
Options to discuss
Cast-in wheel guides
Guides set into new concrete with embedded anchors during yard works, giving a very strong fixing for new-build docks, resurfaced yards and loading bay conversions.
Low-voltage dock light
A swing-arm light fed through a transformer mounted nearby, for sites that prefer a reduced voltage at the lamp head. Same reach and folding action as a mains light.
Which rules apply in England?
Powered doors and dock equipment installed in England may carry the UKCA or the CE mark, and doors are covered by the product standard BS EN 13241. We hand over the relevant documentation for each item fitted in Whitehaven. Planning and Building Regulations questions are never assumed either way: we check what applies at survey, so you know before work is booked.
Questions about dock lights and wheel guides in Whitehaven
Can you work outside our normal operating hours in Whitehaven?
Yes, by arrangement. Evening, night and weekend working can be planned so the installation causes as little disruption as possible to your loading schedule. Out-of-hours work can affect the price, so mention it at the survey and we will include it in the written quote. The agreed times are confirmed in the programme before the job starts.
Will you deal with building control and planning for a project in Whitehaven?
We check at survey whether the work is likely to need approval. Forming a new opening or dock pit may need Building Regulations approval, a building warrant or building control approval, depending on the nation, and external structures such as loading houses can need planning permission. Where approval is needed, we explain what is involved, work with your designer or agent, and build it into the programme.
How do you price dock lights and wheel guides for a site in Whitehaven?
Guide budgets for supply and fit are £280 to £950 per item, excluding VAT. The figure moves with size, insulation, the operator, electrics, access, any pit or groundworks and out-of-hours working. Where levellers are involved, the guide assumes an existing, sound pit. After the free survey you receive a fixed written quote, and that is the price for the agreed scope.
How long should wheel guides be?
Wheel guides need to be long enough to straighten the trailer before it reaches the bumpers, and the right length depends on your yard and approach. Tight yards where drivers turn late usually need longer guides with a flared entry. We set the length and spacing at survey.
Do wheel guides damage tyres?
Correctly spaced wheel guides should not damage tyres. They are set slightly wider than the trailer track so the tyre only brushes the guide when the trailer is off line, and a flared entry stops tyres hitting the end. Guides that are bent or set too narrow should be corrected.
Dock lights and wheel guides near Whitehaven
Looking beyond Whitehaven? Our pages for Workington (7 miles) describe the same loading bay services and how to get in touch.
Other loading bay services in Whitehaven
Full guide to dock lights and wheel guides · Everything we do in Whitehaven
Send a few photos of the dock and a short description of the problem, and we will come back to you about your Whitehaven site.