- Location
- Bishop Auckland, County Durham
- Main postcode district
- DL14
- Nearby (straight line)
- Spennymoor (4 miles), Newton Aycliffe (5 miles) and Durham (9 miles)
- Survey and quote
- Free, with a fixed written quote
Dock lights and wheel guides are two simple loading bay aids. A dock light is a lamp, usually LED, on a swing arm beside the dock door that shines into the trailer so forklift drivers can see the load. Wheel guides are steel rails fixed to the yard that steer the rear wheels so the trailer arrives straight and centred on the leveller.
Why do sites in Bishop Auckland choose this?
Any site in Bishop Auckland considering these items gets the same survey and fixed written quote that we provide across England, Scotland, Wales and Northern Ireland. A landlord preparing a unit in Bishop Auckland for re-letting can add dock lights and wheel guides at modest cost to make the bays more practical.
Resurfacing works on a yard in Bishop Auckland are an ideal moment to fit cast-in wheel guides, before the concrete is finished and bays come back into use.
If you are planning dock lights and wheel guides for a site in Bishop Auckland, expect four stages. A free survey and fixed written quote come first. We then agree a programme with you, including any out-of-hours work. Specialist installation engineers carry out the installation under our management, with us as your single point of contact. Finally, the equipment is tested, your staff are shown how it works and everything is handed over with its documentation.
What happens on site when dock lights or wheel guides are fitted?
Dock lights are fitted from inside the building and usually leave the bay usable for most of the work, while wheel guides close the bay to vehicles until the anchors have cured.
- Dock lights: the bracket is fixed beside the door, the arm and head fitted, and the supply connected and tested. The circuit is isolated briefly during connection.
- Wheel guides: the yard in front of the bay is coned off, guides are set out, drilled and anchored, and the resin is left to cure before trailers return.
- Concrete bases: where tarmac needs a concrete strip first, the bay stays closed until the concrete has gained enough strength.
We ask you to provide a clear bay, details of the nearest power supply, safe yard access and someone who can manage vehicle movements around the work area. Planning guide installation for a quieter period keeps disruption to a minimum.
Which type of dock light is best for a loading bay?
An LED swing-arm dock light is the usual choice for a loading bay, because it reaches into the trailer during loading and folds back flat against the wall when the bay is closed. LED heads run much cooler than older lamps and cope better with knocks and vibration.
- Arm length: longer arms push light further into deep trailers, but need clear wall space so they can fold away from the door path.
- Rigid or flexible arm: a rigid arm with a pivoting head is tougher; a flexible section can be easier to aim.
- Guarding: a protective cage or polycarbonate cover helps the head survive forklift contact.
- Switching: a switch on the head or on the wall, or linked to the door so the light comes on as it opens.
- Supply voltage: mains or low-voltage, confirmed at survey to suit your site.
The light is mounted inside the building beside the door, clear of the door tracks, at a height that lets it swing over the leveller and into the trailer.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What we look at on site
- Scope to convert ground-level doors into docks or add lift tables
- Wind exposure at the dock, which affects door and shelter choice
- Bumper position and wear or damage on the dock face
- Condition of any existing leveller pit, kerb angles and pit drainage
- Drainage on recessed or sloping dock approaches
- Lighting inside trailers and at the dock face
Options to discuss
Cast-in wheel guides
Guides set into new concrete with embedded anchors during yard works, giving a very strong fixing for new-build docks, resurfaced yards and loading bay conversions.
LED swing-arm dock light
An LED head on a swing arm beside the door, swung into the trailer during loading and folded back flat against the wall when the bay is closed.
Planning, building control and safety law in England
Workplace safety in England is regulated by HSE. For a loading bay in Bishop Auckland, that means doors meeting regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, equipment maintained under PUWER and suitable safeguards against vehicles driving away too early. We check what applies at survey and design the bay accordingly.
Questions about dock lights and wheel guides in Bishop Auckland
How long does installation take at a site in Bishop Auckland?
It depends on the equipment, the number of bays, the condition of the dock and whether any building or electrical work is needed. We agree a programme with you after the survey, setting out which bays are out of use and when. Larger jobs are usually phased so that part of the dock stays open, and out-of-hours working can be arranged.
How do you price dock lights and wheel guides for a site in Bishop Auckland?
Guide budgets for supply and fit are £280 to £950 per item, excluding VAT. The figure moves with size, insulation, the operator, electrics, access, any pit or groundworks and out-of-hours working. Where levellers are involved, the guide assumes an existing, sound pit. After the free survey you receive a fixed written quote, and that is the price for the agreed scope.
Is VAT included in your guide prices for dock lights and wheel guides?
No. Our customers are businesses, so guide prices exclude VAT, which is added at the standard rate. The same guide range applies in County Durham as everywhere else: for dock lights and wheel guides, it is £280 to £950 per item, excluding VAT. It covers supply and fit for a typical installation. Your fixed written quote after the free survey shows the net price, the VAT and exactly what is included.
Where should a dock light be mounted?
A dock light is mounted inside the building beside the door opening, high enough to swing over the leveller and into the trailer. It must fold back flat against the wall, clear of the door tracks and the forklift route, so it is not struck when the bay is not in use.
Can dock lights be fitted without stopping loading?
Usually yes. Dock lights are fitted from inside the building beside the door, and the bay can often keep working except for a short period while the supply is isolated and connected. We agree timings with you so the work fits around trailer arrivals.
Dock lights and wheel guides near Bishop Auckland
If your site is not in Bishop Auckland itself, it may be near one of these: Spennymoor (4 miles), Newton Aycliffe (5 miles) and Durham (9 miles). Pick the closest.
Other loading bay services in Bishop Auckland
Full guide to dock lights and wheel guides · Everything we do in Bishop Auckland
Tell us what is happening at your Bishop Auckland dock, what equipment is there and when it is used, and we will suggest the right next step.