- Location
- Wrexham, Clwyd
- Main postcode district
- LL13
- Nearby (straight line)
- Buckley (9 miles), Chester (11 miles) and Deeside (11 miles)
- Survey and quote
- Free, with a fixed written quote
Dock lights and wheel guides are two simple loading bay aids. A dock light is a lamp, usually LED, on a swing arm beside the dock door that shines into the trailer so forklift drivers can see the load. Wheel guides are steel rails fixed to the yard that steer the rear wheels so the trailer arrives straight and centred on the leveller.
Where does this fit at a dock in Wrexham?
Warehouses in Wrexham loading deep trailers by forklift often find the back of the load hard to see without a dock light reaching into the trailer. On older estates around Wrexham, dock lights may still use outdated lamps, and an LED swing-arm light is a simple upgrade that runs cooler.
A landlord preparing a unit in Wrexham for re-letting can add dock lights and wheel guides at modest cost to make the bays more practical.
We never ask you to commit before you have a fixed price. A free survey at your Wrexham site comes first, followed by a written quote. When the order goes ahead, we plan the installation around your operation, book any out-of-hours working you need and manage the specialist installation engineers on site. The job ends with a full test, a run-through for the people who will use the equipment and a set of handover documents.
What happens on site when dock lights or wheel guides are fitted?
Dock lights are fitted from inside the building and usually leave the bay usable for most of the work, while wheel guides close the bay to vehicles until the anchors have cured.
- Dock lights: the bracket is fixed beside the door, the arm and head fitted, and the supply connected and tested. The circuit is isolated briefly during connection.
- Wheel guides: the yard in front of the bay is coned off, guides are set out, drilled and anchored, and the resin is left to cure before trailers return.
- Concrete bases: where tarmac needs a concrete strip first, the bay stays closed until the concrete has gained enough strength.
We ask you to provide a clear bay, details of the nearest power supply, safe yard access and someone who can manage vehicle movements around the work area. Planning guide installation for a quieter period keeps disruption to a minimum.
Should wheel guides be bolted down or cast in?
Wheel guides are bolted down on an existing sound concrete yard and cast in where new concrete is being laid. Both give a strong fixing; the choice depends on whether the yard is being resurfaced.
- Bolt-down guides: steel tube or channel fixed with resin anchors. Quick to fit to existing bays and easy to replace if damaged.
- Cast-in guides: set into fresh concrete with embedded anchors, suited to new-build docks and conversions.
- Flared entry: an angled lead-in at the yard end catches the wheel early and steers it into line.
- Finish: typically galvanised, or painted yellow and black so drivers can see them in mirrors.
Guides are set out to suit the track width of the trailers you receive, centred on the leveller, and long enough to straighten the trailer before it reaches the bumpers. Tarmac is usually too soft to hold anchors, so a concrete strip or base is laid first. Our guide to choosing dock bumpers and wheel guides covers layout in more depth.
The same published guide range applies across Wales; access, out-of-hours working and site conditions are confirmed at the free survey.
What we look at on site
- Forklift and pallet truck loads crossing the leveller platform
- Wind exposure at the dock, which affects door and shelter choice
- Yard gradient and the slope of the approach to the dock
- Traffic routes for vehicles and separation of pedestrians
- Control positions, isolators and any existing interlocks
- Power supply at each bay, including three-phase availability
Options to discuss
Low-voltage dock light
A swing-arm light fed through a transformer mounted nearby, for sites that prefer a reduced voltage at the lamp head. Same reach and folding action as a mains light.
Bolt-down wheel guides
Steel tube or channel guides fixed with resin anchors into an existing concrete apron, typically galvanised or painted in high-visibility colours for drivers using mirrors.
Planning, building control and safety law in Wales
Sites in Wrexham follow the rules for Wales. Forming a new opening or dock pit may need Building Regulations approval, and loading houses, canopies or new dock approaches can need planning permission from the local planning authority. We check what applies at survey, so any approvals are understood before the programme is fixed.
Questions about dock lights and wheel guides in Wrexham
How long does installation take at a site in Wrexham?
It depends on the equipment, the number of bays, the condition of the dock and whether any building or electrical work is needed. We agree a programme with you after the survey, setting out which bays are out of use and when. Larger jobs are usually phased so that part of the dock stays open, and out-of-hours working can be arranged.
Which building and safety rules apply to a site in Wrexham?
It depends on which UK nation the site is in. England and Wales use Building Regulations approval, Scotland uses building warrants and Northern Ireland uses building control approval from the council. Workplace safety is regulated by HSE in Great Britain and HSENI in Northern Ireland, and energy rules differ between nations. For your site in Wrexham, we check what applies at survey and design to it.
What warranty comes with new loading bay equipment?
New equipment comes with the manufacturer's warranty, which varies by product. Our workmanship terms are set out in writing in the quote for your Wrexham site, so you can see what is covered before you commit. Check the warranty terms for any servicing conditions, and we can quote for planned maintenance once the installation is complete.
Can wheel guides be fitted to a tarmac yard?
Wheel guides can be fitted to a tarmac yard, but tarmac is usually too soft to hold anchors on its own. The normal approach is to cut out a strip and lay a concrete base for the guides. That work is identified at survey and included in the written quote.
Where should a dock light be mounted?
A dock light is mounted inside the building beside the door opening, high enough to swing over the leveller and into the trailer. It must fold back flat against the wall, clear of the door tracks and the forklift route, so it is not struck when the bay is not in use.
Dock lights and wheel guides near Wrexham
Businesses outside Wrexham may find their nearest town in this list: Buckley (9 miles), Chester (11 miles) and Deeside (11 miles). Each page covers doors, docks, repairs and servicing.
Other loading bay services in Wrexham
Full guide to dock lights and wheel guides · Everything we do in Wrexham
For a written price on loading bay work in Wrexham, request a quote and include photos of the bay if you can.