- Location
- Peterborough, Cambridgeshire
- Main postcode district
- PE1
- Nearby (straight line)
- Stamford (11 miles), March (14 miles) and Spalding (15 miles)
- Survey and quote
- Free, with a fixed written quote
Dock lights and wheel guides are two simple loading bay aids. A dock light is a lamp, usually LED, on a swing arm beside the dock door that shines into the trailer so forklift drivers can see the load. Wheel guides are steel rails fixed to the yard that steer the rear wheels so the trailer arrives straight and centred on the leveller.
How does this suit sites in Peterborough?
On older estates around Peterborough, dock lights may still use outdated lamps, and an LED swing-arm light is a simple upgrade that runs cooler. Shelters and seals at sites near Peterborough last longer when wheel guides keep trailers centred, because off-centre parking is a common cause of torn curtains.
Resurfacing works on a yard in Peterborough are an ideal moment to fit cast-in wheel guides, before the concrete is finished and bays come back into use.
If you are planning dock lights and wheel guides for a site in Peterborough, expect four stages. A free survey and fixed written quote come first. We then agree a programme with you, including any out-of-hours work. Specialist installation engineers carry out the installation under our management, with us as your single point of contact. Finally, the equipment is tested, your staff are shown how it works and everything is handed over with its documentation.
One feature of the freight network near Peterborough is worth a mention: large distribution parks sit close to the A1(M) and the A47. Busy or quiet, a dock needs equipment sized for the vehicles it receives.
Do health and safety rules cover dock lights and wheel guides?
Dock lights and wheel guides support your wider loading bay safety duties rather than replacing them. Once fitted, a dock light is work equipment under the Provision and Use of Work Equipment Regulations 1998 (PUWER), so it must be suitable, maintained in a safe condition and inspected where deterioration could lead to danger. In Northern Ireland the equivalent is PUWER (Northern Ireland) 1999.
HSE's guide to workplace transport safety (HSG136) is the main reference for managing vehicles in the yard, and its loading guidance says there should be safeguards against drivers driving away too early, such as traffic lights, restraints or key control. Wheel guides and dock lights do not meet that requirement on their own, but they help drivers park accurately and help dock staff see what they are doing.
Electrical work for dock lights is carried out by qualified electricians and tested before use. The regulator is HSE in Great Britain and HSENI in Northern Ireland.
What happens on site when dock lights or wheel guides are fitted?
Dock lights are fitted from inside the building and usually leave the bay usable for most of the work, while wheel guides close the bay to vehicles until the anchors have cured.
- Dock lights: the bracket is fixed beside the door, the arm and head fitted, and the supply connected and tested. The circuit is isolated briefly during connection.
- Wheel guides: the yard in front of the bay is coned off, guides are set out, drilled and anchored, and the resin is left to cure before trailers return.
- Concrete bases: where tarmac needs a concrete strip first, the bay stays closed until the concrete has gained enough strength.
We ask you to provide a clear bay, details of the nearest power supply, safe yard access and someone who can manage vehicle movements around the work area. Planning guide installation for a quieter period keeps disruption to a minimum.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What we look at on site
- Power supply at each bay, including three-phase availability
- Scope to convert ground-level doors into docks or add lift tables
- Clear opening width and height for each door
- Wind exposure at the dock, which affects door and shelter choice
- Lighting inside trailers and at the dock face
- Working hours, shift patterns and windows for out-of-hours work
Options to discuss
Bolt-down wheel guides
Steel tube or channel guides fixed with resin anchors into an existing concrete apron, typically galvanised or painted in high-visibility colours for drivers using mirrors.
Cast-in wheel guides
Guides set into new concrete with embedded anchors during yard works, giving a very strong fixing for new-build docks, resurfaced yards and loading bay conversions.
What do the rules in England mean for the work?
Workplace safety in England is regulated by HSE. For a loading bay in Peterborough, that means doors meeting regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, equipment maintained under PUWER and suitable safeguards against vehicles driving away too early. We check what applies at survey and design the bay accordingly.
Questions about dock lights and wheel guides in Peterborough
What warranty comes with new loading bay equipment?
New equipment comes with the manufacturer's warranty, which varies by product. Our workmanship terms are set out in writing in the quote for your Peterborough site, so you can see what is covered before you commit. Check the warranty terms for any servicing conditions, and we can quote for planned maintenance once the installation is complete.
Will you deal with building control and planning for a project in Peterborough?
We check at survey whether the work is likely to need approval. Forming a new opening or dock pit may need Building Regulations approval, a building warrant or building control approval, depending on the nation, and external structures such as loading houses can need planning permission. Where approval is needed, we explain what is involved, work with your designer or agent, and build it into the programme.
How long does installation take at a site in Peterborough?
It depends on the equipment, the number of bays, the condition of the dock and whether any building or electrical work is needed. We agree a programme with you after the survey, setting out which bays are out of use and when. Larger jobs are usually phased so that part of the dock stays open, and out-of-hours working can be arranged.
How long should wheel guides be?
Wheel guides need to be long enough to straighten the trailer before it reaches the bumpers, and the right length depends on your yard and approach. Tight yards where drivers turn late usually need longer guides with a flared entry. We set the length and spacing at survey.
Where should a dock light be mounted?
A dock light is mounted inside the building beside the door opening, high enough to swing over the leveller and into the trailer. It must fold back flat against the wall, clear of the door tracks and the forklift route, so it is not struck when the bay is not in use.
Dock lights and wheel guides near Peterborough
The same survey, quote and repair service is available in towns around Peterborough, such as Stamford (11 miles), March (14 miles) and Spalding (15 miles).
Other loading bay services in Peterborough
Full guide to dock lights and wheel guides · Everything we do in Peterborough
For a written price on loading bay work in Peterborough, request a quote and include photos of the bay if you can.