- Location
- Dunstable, Bedfordshire
- Main postcode district
- LU6
- Nearby (straight line)
- Luton (5 miles), Leighton Buzzard (6 miles) and Harpenden (9 miles)
- Survey and quote
- Free, with a fixed written quote
Dock lights and wheel guides are two simple loading bay aids. A dock light is a lamp, usually LED, on a swing arm beside the dock door that shines into the trailer so forklift drivers can see the load. Wheel guides are steel rails fixed to the yard that steer the rear wheels so the trailer arrives straight and centred on the leveller.
Where does this fit at a dock in Dunstable?
On older estates around Dunstable, dock lights may still use outdated lamps, and an LED swing-arm light is a simple upgrade that runs cooler. Resurfacing works on a yard in Dunstable are an ideal moment to fit cast-in wheel guides, before the concrete is finished and bays come back into use.
Shelters and seals at sites near Dunstable last longer when wheel guides keep trailers centred, because off-centre parking is a common cause of torn curtains.
The survey is free, the quote is written and the price is fixed: that is how every installation in Dunstable begins. We then manage the work from start to finish. Fitting is carried out by specialist installers under our management, phased so the operation keeps moving, and nights or weekends can be booked by arrangement. On the final day we test the equipment with you and hand over the operating and maintenance information.
What happens on site when dock lights or wheel guides are fitted?
Dock lights are fitted from inside the building and usually leave the bay usable for most of the work, while wheel guides close the bay to vehicles until the anchors have cured.
- Dock lights: the bracket is fixed beside the door, the arm and head fitted, and the supply connected and tested. The circuit is isolated briefly during connection.
- Wheel guides: the yard in front of the bay is coned off, guides are set out, drilled and anchored, and the resin is left to cure before trailers return.
- Concrete bases: where tarmac needs a concrete strip first, the bay stays closed until the concrete has gained enough strength.
We ask you to provide a clear bay, details of the nearest power supply, safe yard access and someone who can manage vehicle movements around the work area. Planning guide installation for a quieter period keeps disruption to a minimum.
How much do dock lights and wheel guides cost?
Dock lights and wheel guides typically cost £280 to £950 per item, supplied and fitted, excluding VAT, where an item is one dock light or one wheel guide. A standard LED swing-arm light usually sits in the lower half of the range; long, heavy-section or cast-in guides sit towards the top.
What moves the price:
- Light specification: arm length, LED head output, protective guarding and whether a low-voltage supply is needed.
- Power: the distance to a suitable supply and how the cable is contained.
- Guide length and section: longer guides and heavier steel cost more.
- Yard surface: sound concrete takes anchors directly; tarmac usually needs a concrete base first, priced after survey.
- Number of bays: fitting several bays in one visit lowers the cost per item.
These are guide budgets. After a free site survey we send a written quote, which is the fixed price. VAT is added at the standard rate.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What do we check at the survey?
- Lighting inside trailers and at the dock face
- Whether planning, building control or a building warrant may be needed
- Wheel guide positions and yard markings for reversing vehicles
- Clear opening width and height for each door
- Forklift and pallet truck loads crossing the leveller platform
- Traffic routes for vehicles and separation of pedestrians
Options to discuss
Cast-in wheel guides
Guides set into new concrete with embedded anchors during yard works, giving a very strong fixing for new-build docks, resurfaced yards and loading bay conversions.
Low-voltage dock light
A swing-arm light fed through a transformer mounted nearby, for sites that prefer a reduced voltage at the lamp head. Same reach and folding action as a mains light.
What do the rules in England mean for the work?
Workplace safety in England is regulated by HSE. For a loading bay in Dunstable, that means doors meeting regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, equipment maintained under PUWER and suitable safeguards against vehicles driving away too early. We check what applies at survey and design the bay accordingly.
Questions about dock lights and wheel guides in Dunstable
Is VAT included in your guide prices for dock lights and wheel guides?
No. Our customers are businesses, so guide prices exclude VAT, which is added at the standard rate. The same guide range applies in Bedfordshire as everywhere else: for dock lights and wheel guides, it is £280 to £950 per item, excluding VAT. It covers supply and fit for a typical installation. Your fixed written quote after the free survey shows the net price, the VAT and exactly what is included.
Is the site survey in Dunstable free?
Yes. For new installations, replacements, upgrades, conversions and complete bays, the site survey and written quote are free and come with no obligation. The survey lets us measure the openings, check the dock and structure, and understand how the bay is used, so the quote reflects your site. Repair and servicing visits are different: they are chargeable, with the price agreed before anyone attends.
Which building and safety rules apply to a site in Dunstable?
It depends on which UK nation the site is in. England and Wales use Building Regulations approval, Scotland uses building warrants and Northern Ireland uses building control approval from the council. Workplace safety is regulated by HSE in Great Britain and HSENI in Northern Ireland, and energy rules differ between nations. For your site in Dunstable, we check what applies at survey and design to it.
Do wheel guides damage tyres?
Correctly spaced wheel guides should not damage tyres. They are set slightly wider than the trailer track so the tyre only brushes the guide when the trailer is off line, and a flared entry stops tyres hitting the end. Guides that are bent or set too narrow should be corrected.
Can wheel guides be fitted to a tarmac yard?
Wheel guides can be fitted to a tarmac yard, but tarmac is usually too soft to hold anchors on its own. The normal approach is to cut out a strip and lay a concrete base for the guides. That work is identified at survey and included in the written quote.
Dock lights and wheel guides near Dunstable
Sites close to Dunstable get the same service, including those in Luton (5 miles), Leighton Buzzard (6 miles) and Harpenden (9 miles), with every job run the same way.
Other loading bay services in Dunstable
Full guide to dock lights and wheel guides · Everything we do in Dunstable
Speak to us about your Dunstable loading bay. We will ask the right questions, then set out the next step clearly.