- Location
- Shirley, West Midlands
- Main postcode district
- B90
- Nearby (straight line)
- Solihull (2 miles), Birmingham (6 miles) and Washwood Heath (6 miles)
- Visit pricing
- Agreed in writing before we attend
Dock leveller repair covers finding and fixing faults on the bridge between the dock and the trailer bed, including hydraulic cylinders, hoses and power packs, safety and check valves, lip hinges and lip cylinders, platform and lip damage, toe guards and control panels. It applies to swing-lip, telescopic-lip, mechanical and edge-of-dock levellers, with the aim of returning each one to safe working order.
Is this right for your site in Shirley?
When a leveller at a warehouse near Shirley sinks under load, it should be taken out of use until the hydraulic cause has been found and fixed. Insurer inspections at sites around Shirley may list leveller defects that need attention, and we can price each item directly from the report.
Every leveller repair enquiry from Shirley starts with you describing the fault, then a visit price agreed in writing before an engineer attends.
Planned servicing and reactive repairs in Shirley are both chargeable. We agree the price of each visit in writing beforehand, and we never extend the scope without asking. Photos taken by your team help us plan the work and the parts. The engineer records the condition of doors, levellers, shelters and safety equipment as they go, and you receive that as a written report after the visit.
What are the most common dock leveller faults?
The most common dock leveller faults are hydraulic leaks, power pack failures, lip and hinge damage, and control faults. The way the leveller behaves usually points to the cause.
- Will not rise, or rises slowly: power pack motor or pump, low oil, a failed contactor or a control fault.
- Sinks under load or drifts down when parked: leaking cylinder seals or a faulty check valve.
- Drops suddenly, then locks: the safety valve doing its job after a hose or fitting failure.
- Lip will not extend or falls short: a lip cylinder fault, a sequence valve problem or a seized lip hinge.
- Oil in the pit: a leaking hose, fitting or cylinder.
- Jerky or noisy movement: air in the hydraulics or worn pivots.
- Cracked deck, bent lip or broken hinge knuckles: impact damage or fatigue.
A leveller showing any of these faults should be taken out of use until it has been checked.
Should a dock leveller be repaired or replaced?
A dock leveller is usually worth repairing when the platform, lip and hinges are structurally sound and the fault is in the hydraulics, controls or a single component. Replacement is worth considering when the structure is fatigued or the leveller no longer suits your trailers.
Repair is likely to be the better option when:
- the fault is a hose, cylinder, valve or power pack;
- lip or hinge damage is limited to one area and can be welded or rebuilt;
- the leveller is the right length for your trailer height range.
Replacement is worth pricing when:
- the deck or hinge structure is cracking in several places;
- hydraulic failures keep recurring despite repairs;
- an old mechanical leveller needs major parts that are hard to find;
- trailers now arrive at heights the leveller cannot reach at a safe gradient.
Our guide to dock leveller repair or replace covers the signs in more detail.
The visit price is agreed before anyone attends. Parts and any extra work are quoted before they are fitted.
What else does the engineer check at the bay?
- Pit frame welds, platform cracks and structural damage
- Door panels, side seals and bottom rubbers
- Previous service and inspection records, where available
- Shelter curtains, frames and side pads for tears
- Track alignment, rollers and wall fixings
- Hydraulic oil level, hoses and cylinders for leaks
Options to discuss
Lip and hinge repairs
Seized or worn lip hinges rebuilt, hinge pins replaced, bent lips straightened or replaced, and lip cylinders repaired so the lip extends fully on to the trailer bed.
Power pack repairs
Motor, pump, valve block and contactor faults diagnosed and repaired, or the whole power pack replaced as a unit where that is the more economical option.
What do the rules in England mean for the work?
Lift tables and dock lifts in Shirley may fall under LOLER, with thorough examination at least every 12 months, or every 6 months where people are lifted. It depends on the equipment and how it is used, and your insurer or competent person will confirm. Dock levellers are usually treated as work equipment under PUWER. We check what applies before any work starts.
Questions about dock leveller repairs in Shirley
Can you take over our existing loading bay maintenance arrangement?
Yes. Send us a list of the equipment at your Shirley site, with makes, models and approximate ages if known, plus recent service or inspection reports. We will propose a planned maintenance schedule and price it per item per visit. The first visit records the condition of everything, so you have a clear starting point for future servicing.
What is the difference between servicing and a statutory inspection?
Servicing keeps equipment working: cleaning, adjusting, lubricating and replacing worn parts. A statutory inspection or thorough examination is a separate check by a competent person, often arranged through your engineering insurer. Dock levellers are commonly inspected under PUWER at 12-month intervals, and lift tables may need LOLER thorough examination, depending on the equipment and how it is used. Your insurer or competent person will confirm what applies.
Do you provide a written report after each visit?
Yes. After every repair or service visit to a site in Shirley, you receive a written report setting out what was checked, what was found, what work was carried out and anything that still needs attention, with a quote for further work where needed. The report is useful for your maintenance records and for discussions with your insurer or inspector.
Can a leveller be repaired without disturbing the pit?
Usually yes. Most leveller repairs are carried out in place, working from the deck or from the pit with the platform propped. If the pit itself is cracked, broken at the edges or holding water, that is noted in the report and any pit repair is priced separately.
Can leveller repairs be done outside operating hours?
Yes, leveller repairs can be arranged for evenings or weekends where that suits your operation. Out-of-hours working costs more, and that is included in the visit price agreed in writing beforehand. Timing for each repair is agreed with you, and neighbouring bays can usually keep working.
Dock leveller repairs near Shirley
Sites close to Shirley get the same service, including those in Solihull (2 miles), Birmingham (6 miles) and Washwood Heath (6 miles), with every job run the same way.
Other loading bay services in Shirley
Full guide to dock leveller repairs · Everything we do in Shirley
If a loading bay in Shirley needs attention, call us or send photos and details online.