- Location
- Dorking, Surrey
- Main postcode district
- RH4
- Nearby (straight line)
- Leatherhead (4 miles), Reigate (6 miles) and Redhill (7 miles)
- Visit pricing
- Agreed in writing before we attend
Dock leveller repair covers finding and fixing faults on the bridge between the dock and the trailer bed, including hydraulic cylinders, hoses and power packs, safety and check valves, lip hinges and lip cylinders, platform and lip damage, toe guards and control panels. It applies to swing-lip, telescopic-lip, mechanical and edge-of-dock levellers, with the aim of returning each one to safe working order.
Why do sites in Dorking choose this?
Low temperatures at chilled and frozen docks in Dorking can affect hydraulic oil and seals, so it helps to mention the operating temperature when reporting a fault. Older units in Dorking may still run mechanical or early hydraulic levellers, where a well-judged repair can keep the bay working before replacement is needed.
Insurer inspections at sites around Dorking may list leveller defects that need attention, and we can price each item directly from the report.
Tell us what has gone wrong at your Dorking site and, if you can, send photos of the fault and any labels on the equipment. We then confirm the visit price in writing, and nobody attends until you have agreed it. On site, the engineer diagnoses and repairs what was agreed; anything extra is quoted first, never added without your say-so. A written report follows, covering findings, work carried out and recommendations.
Can you repair defects listed on an insurer inspection report?
Yes. Repairing defects from an engineering insurer's inspection report is one of the most common reasons for a leveller repair visit. Sending us the report is the quickest way to get an accurate price.
How it works:
- Send the report: we read each defect against the leveller it refers to, with any photos you can add.
- Price each item: we agree the visit price in writing, listing the defects it covers.
- Repair: the engineer carries out the listed repairs, and any further defects found are quoted before work.
- Record: the written report shows which defects were cleared and how, which you can keep with the insurer's report.
Any re-inspection by the insurer is arranged between you and them. If a defect is marked as dangerous, the leveller should stay out of use until it has been repaired.
Grouping several levellers' defects into one visit usually keeps the cost per item down.
What inspection rules apply to dock levellers?
Dock levellers are work equipment under the Provision and Use of Work Equipment Regulations 1998 (PUWER), so they must be maintained in a safe condition and inspected where deterioration could lead to danger. In Northern Ireland the equivalent is PUWER (Northern Ireland) 1999.
Engineering insurers commonly inspect dock levellers under PUWER at 12-month intervals. Their reports list defects, sometimes marked for action before further use, and repairs are often needed to clear them.
Most levellers are treated as work equipment under PUWER. A leveller designed or used to lift people may fall under the Lifting Operations and Lifting Equipment Regulations (LOLER), with 6-monthly thorough examination. This depends on the equipment and how it is used; your insurer or competent person will confirm.
Levellers are made to BS EN 1398:2009, the dock leveller safety standard. HSE guidance notes that guards or skirting may be needed where something could be caught, so damaged toe guards are repaired as part of the job. See our guide to dock leveller inspections under PUWER and LOLER.
The visit price is agreed before anyone attends. Parts and any extra work are quoted before they are fitted.
Bay checks on a repair or service visit
- Leveller toe guards and side skirting, where fitted
- Control panels, push buttons and emergency stops
- Pit frame welds, platform cracks and structural damage
- Wiring, isolators and motor performance under load
- Manual override and emergency operation on powered doors
- Track alignment, rollers and wall fixings
Options to discuss
Lip and hinge repairs
Seized or worn lip hinges rebuilt, hinge pins replaced, bent lips straightened or replaced, and lip cylinders repaired so the lip extends fully on to the trailer bed.
Control and safety repairs
Control panels, push buttons, limit switches, maintenance struts, toe guards and side skirts repaired or replaced so the leveller operates and parks safely.
Which rules apply in England?
Lift tables and dock lifts in Dorking may fall under LOLER, with thorough examination at least every 12 months, or every 6 months where people are lifted. It depends on the equipment and how it is used, and your insurer or competent person will confirm. Dock levellers are usually treated as work equipment under PUWER. We check what applies before any work starts.
Questions about dock leveller repairs in Dorking
Can you take over our existing loading bay maintenance arrangement?
Yes. Send us a list of the equipment at your Dorking site, with makes, models and approximate ages if known, plus recent service or inspection reports. We will propose a planned maintenance schedule and price it per item per visit. The first visit records the condition of everything, so you have a clear starting point for future servicing.
What is the difference between servicing and a statutory inspection?
Servicing keeps equipment working: cleaning, adjusting, lubricating and replacing worn parts. A statutory inspection or thorough examination is a separate check by a competent person, often arranged through your engineering insurer. Dock levellers are commonly inspected under PUWER at 12-month intervals, and lift tables may need LOLER thorough examination, depending on the equipment and how it is used. Your insurer or competent person will confirm what applies.
Can you repair all makes of loading bay equipment?
We work on common makes and types of doors, dock levellers, shelters, seals and restraints. Parts availability varies, particularly for older or discontinued equipment, so it helps to send the make, model and photos of any data plates from your site in Dorking. If original parts are not available, we tell you and price the alternatives, including replacement where that makes more sense.
Will the repair clear an insurer's defect notice?
A repair addresses the defect listed, and our written report records what was found and what was done, which you can keep with the insurer's report. Whether the insurer needs to re-inspect is between you and them. Any further defects found during the repair are quoted before work.
Do you repair mechanical dock levellers?
Yes, where parts are still available. Mechanical levellers use springs and a hold-down mechanism rather than hydraulics, and common repairs include springs, release mechanisms and lip hinges. Where parts are hard to find or faults keep recurring, the report may suggest pricing a hydraulic replacement.
Dock leveller repairs near Dorking
Close neighbours of Dorking with their own pages here: Leatherhead (4 miles), Reigate (6 miles) and Redhill (7 miles). Choose one to see coverage details for that town.
Other loading bay services in Dorking
Full guide to dock leveller repairs · Everything we do in Dorking
Ready to talk about a loading bay in Dorking? Call us, or send the details through the quote form.