- Location
- Frome, Somerset
- Main postcode district
- BA11
- Nearby (straight line)
- Westbury (6 miles), Warminster (6 miles) and Trowbridge (8 miles)
- Visit pricing
- Agreed in writing before we attend
Dock leveller repair covers finding and fixing faults on the bridge between the dock and the trailer bed, including hydraulic cylinders, hoses and power packs, safety and check valves, lip hinges and lip cylinders, platform and lip damage, toe guards and control panels. It applies to swing-lip, telescopic-lip, mechanical and edge-of-dock levellers, with the aim of returning each one to safe working order.
Is this right for your site in Frome?
Docks in Frome receiving trailers at widely varying bed heights can wear lip hinges faster, and hinge rebuilds are a routine part of leveller repair. Distribution docks in Frome that run several shifts put heavy cycles through leveller hydraulics, so leaks and slow operation can show up sooner.
Every leveller repair enquiry from Frome starts with you describing the fault, then a visit price agreed in writing before an engineer attends.
When something stops working at a loading bay in Frome, contact us with a description and, ideally, photos. We will confirm the cost of the visit in writing before booking anyone. If the engineer finds the problem goes further than expected, you receive a quote for the additional work and decide whether to proceed. Every visit is followed by a written report you can keep with your maintenance records.
What inspection rules apply to dock levellers?
Dock levellers are work equipment under the Provision and Use of Work Equipment Regulations 1998 (PUWER), so they must be maintained in a safe condition and inspected where deterioration could lead to danger. In Northern Ireland the equivalent is PUWER (Northern Ireland) 1999.
Engineering insurers commonly inspect dock levellers under PUWER at 12-month intervals. Their reports list defects, sometimes marked for action before further use, and repairs are often needed to clear them.
Most levellers are treated as work equipment under PUWER. A leveller designed or used to lift people may fall under the Lifting Operations and Lifting Equipment Regulations (LOLER), with 6-monthly thorough examination. This depends on the equipment and how it is used; your insurer or competent person will confirm.
Levellers are made to BS EN 1398:2009, the dock leveller safety standard. HSE guidance notes that guards or skirting may be needed where something could be caught, so damaged toe guards are repaired as part of the job. See our guide to dock leveller inspections under PUWER and LOLER.
Can you repair defects listed on an insurer inspection report?
Yes. Repairing defects from an engineering insurer's inspection report is one of the most common reasons for a leveller repair visit. Sending us the report is the quickest way to get an accurate price.
How it works:
- Send the report: we read each defect against the leveller it refers to, with any photos you can add.
- Price each item: we agree the visit price in writing, listing the defects it covers.
- Repair: the engineer carries out the listed repairs, and any further defects found are quoted before work.
- Record: the written report shows which defects were cleared and how, which you can keep with the insurer's report.
Any re-inspection by the insurer is arranged between you and them. If a defect is marked as dangerous, the leveller should stay out of use until it has been repaired.
Grouping several levellers' defects into one visit usually keeps the cost per item down.
The visit price is agreed before anyone attends. Parts and any extra work are quoted before they are fitted.
What we look at around the bay
- Vehicle restraint engagement and its signal sequence
- Pit frame welds, platform cracks and structural damage
- Traffic light function and interlock operation
- Lip hinge, lip extension and lip support operation
- Hydraulic oil level, hoses and cylinders for leaks
- Anti-fall device on upward-opening doors
Options to discuss
Structural and weld repairs
Cracked deck plates, broken welds and damaged front sections repaired by welding or with fabricated replacement parts, restoring the platform's strength.
Lip and hinge repairs
Seized or worn lip hinges rebuilt, hinge pins replaced, bent lips straightened or replaced, and lip cylinders repaired so the lip extends fully on to the trailer bed.
Planning, building control and safety law in England
Workplace safety in England is regulated by HSE. For a loading bay in Frome, that means doors meeting regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, equipment maintained under PUWER and suitable safeguards against vehicles driving away too early. We check what applies before any work starts and design the bay accordingly.
Questions about dock leveller repairs in Frome
How is a repair or service visit in Frome priced?
Repair and service visits are chargeable, and the price is agreed in writing before anyone attends. For dock leveller repairs, the guide budget is £220 to £2,600 per repair, excluding VAT. The exact figure depends on the fault, parts, access and timing. If the engineer finds further work on the day, it is quoted for your approval before it is carried out.
How often should equipment at our Frome site be serviced?
It depends on how hard the equipment works and on the manufacturer's recommendations. A multi-shift dock with frequent trailer movements needs more attention than a door that opens a few times a day. We suggest a schedule after looking at the equipment and how it is used, and we can line visits up with your insurance inspections where that helps.
What information helps before a repair visit?
Photos or a short video of the fault are the most useful thing you can send, along with the make and model from the data plate, a description of what happens when the equipment is operated and any error codes. For a site in Frome, also tell us about access, parking and site rules. With that, we can price the visit and bring the likely parts.
Can leveller repairs be done outside operating hours?
Yes, leveller repairs can be arranged for evenings or weekends where that suits your operation. Out-of-hours working costs more, and that is included in the visit price agreed in writing beforehand. Timing for each repair is agreed with you, and neighbouring bays can usually keep working.
Can a leveller be repaired without disturbing the pit?
Usually yes. Most leveller repairs are carried out in place, working from the deck or from the pit with the platform propped. If the pit itself is cracked, broken at the edges or holding water, that is noted in the report and any pit repair is priced separately.
Dock leveller repairs near Frome
Distances are measured from Frome. Nearby towns we cover include Westbury (6 miles), Warminster (6 miles) and Trowbridge (8 miles), and other towns in the area are covered too.
Other loading bay services in Frome
Full guide to dock leveller repairs · Everything we do in Frome
Have photos of the door, leveller or shelter? Send them with your enquiry and we can give a clearer answer for your Frome site.