- Location
- Selby, North Yorkshire
- Main postcode district
- YO8
- Nearby (straight line)
- Goole (10 miles), Pontefract (12 miles) and York (12 miles)
- Visit pricing
- Agreed in writing before we attend
Dock leveller repair covers finding and fixing faults on the bridge between the dock and the trailer bed, including hydraulic cylinders, hoses and power packs, safety and check valves, lip hinges and lip cylinders, platform and lip damage, toe guards and control panels. It applies to swing-lip, telescopic-lip, mechanical and edge-of-dock levellers, with the aim of returning each one to safe working order.
What matters for dock leveller repairs in Selby?
Landlords and managing agents in Selby with several units can group leveller repairs into planned visits, keeping access costs down across the estate. Distribution docks in Selby that run several shifts put heavy cycles through leveller hydraulics, so leaks and slow operation can show up sooner.
When a leveller at a warehouse near Selby sinks under load, it should be taken out of use until the hydraulic cause has been found and fixed.
Planned servicing and reactive repairs in Selby are both chargeable. We agree the price of each visit in writing beforehand, and we never extend the scope without asking. Photos taken by your team help us plan the work and the parts. The engineer records the condition of doors, levellers, shelters and safety equipment as they go, and you receive that as a written report after the visit.
What are the most common dock leveller faults?
The most common dock leveller faults are hydraulic leaks, power pack failures, lip and hinge damage, and control faults. The way the leveller behaves usually points to the cause.
- Will not rise, or rises slowly: power pack motor or pump, low oil, a failed contactor or a control fault.
- Sinks under load or drifts down when parked: leaking cylinder seals or a faulty check valve.
- Drops suddenly, then locks: the safety valve doing its job after a hose or fitting failure.
- Lip will not extend or falls short: a lip cylinder fault, a sequence valve problem or a seized lip hinge.
- Oil in the pit: a leaking hose, fitting or cylinder.
- Jerky or noisy movement: air in the hydraulics or worn pivots.
- Cracked deck, bent lip or broken hinge knuckles: impact damage or fatigue.
A leveller showing any of these faults should be taken out of use until it has been checked.
What inspection rules apply to dock levellers?
Dock levellers are work equipment under the Provision and Use of Work Equipment Regulations 1998 (PUWER), so they must be maintained in a safe condition and inspected where deterioration could lead to danger. In Northern Ireland the equivalent is PUWER (Northern Ireland) 1999.
Engineering insurers commonly inspect dock levellers under PUWER at 12-month intervals. Their reports list defects, sometimes marked for action before further use, and repairs are often needed to clear them.
Most levellers are treated as work equipment under PUWER. A leveller designed or used to lift people may fall under the Lifting Operations and Lifting Equipment Regulations (LOLER), with 6-monthly thorough examination. This depends on the equipment and how it is used; your insurer or competent person will confirm.
Levellers are made to BS EN 1398:2009, the dock leveller safety standard. HSE guidance notes that guards or skirting may be needed where something could be caught, so damaged toe guards are repaired as part of the job. See our guide to dock leveller inspections under PUWER and LOLER.
The visit price is agreed before anyone attends. Parts and any extra work are quoted before they are fitted.
Checks made while we are on site
- Door panels, side seals and bottom rubbers
- Shelter curtains, frames and side pads for tears
- Inflatable shelter fans, airbags and control function
- Manual override and emergency operation on powered doors
- Lip hinge, lip extension and lip support operation
- Track alignment, rollers and wall fixings
Options to discuss
Structural and weld repairs
Cracked deck plates, broken welds and damaged front sections repaired by welding or with fabricated replacement parts, restoring the platform's strength.
Lip and hinge repairs
Seized or worn lip hinges rebuilt, hinge pins replaced, bent lips straightened or replaced, and lip cylinders repaired so the lip extends fully on to the trailer bed.
What do the rules in England mean for the work?
Workplace safety in England is regulated by HSE. For a loading bay in Selby, that means doors meeting regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, equipment maintained under PUWER and suitable safeguards against vehicles driving away too early. We check what applies before any work starts and design the bay accordingly.
Questions about dock leveller repairs in Selby
Do you provide a written report after each visit?
Yes. After every repair or service visit to a site in Selby, you receive a written report setting out what was checked, what was found, what work was carried out and anything that still needs attention, with a quote for further work where needed. The report is useful for your maintenance records and for discussions with your insurer or inspector.
Do you cover North Yorkshire for dock leveller repairs?
Yes. We take on dock leveller repairs for sites in Selby and throughout North Yorkshire. Each visit is arranged in advance, with the price agreed in writing before anyone attends. Specialist service engineers working under our management carry out the work, and we remain your point of contact from the first call to the written report.
Can you repair all makes of loading bay equipment?
We work on common makes and types of doors, dock levellers, shelters, seals and restraints. Parts availability varies, particularly for older or discontinued equipment, so it helps to send the make, model and photos of any data plates from your site in Selby. If original parts are not available, we tell you and price the alternatives, including replacement where that makes more sense.
Can a leveller be repaired without disturbing the pit?
Usually yes. Most leveller repairs are carried out in place, working from the deck or from the pit with the platform propped. If the pit itself is cracked, broken at the edges or holding water, that is noted in the report and any pit repair is priced separately.
Do you repair mechanical dock levellers?
Yes, where parts are still available. Mechanical levellers use springs and a hold-down mechanism rather than hydraulics, and common repairs include springs, release mechanisms and lip hinges. Where parts are hard to find or faults keep recurring, the report may suggest pricing a hydraulic replacement.
Dock leveller repairs near Selby
Sites close to Selby get the same service, including those in Goole (10 miles), Pontefract (12 miles) and York (12 miles), with every job run the same way.
Other loading bay services in Selby
Full guide to dock leveller repairs · Everything we do in Selby
For a written price on loading bay work in Selby, request a quote and include photos of the bay if you can.