- Location
- Loughborough, Leicestershire
- Main postcode district
- LE11
- Nearby (straight line)
- Mountsorrel (4 miles), Coalville (8 miles) and Castle Donington (8 miles)
- Visit pricing
- Agreed in writing before we attend
Dock leveller repair covers finding and fixing faults on the bridge between the dock and the trailer bed, including hydraulic cylinders, hoses and power packs, safety and check valves, lip hinges and lip cylinders, platform and lip damage, toe guards and control panels. It applies to swing-lip, telescopic-lip, mechanical and edge-of-dock levellers, with the aim of returning each one to safe working order.
Is this right for your site in Loughborough?
Insurer inspections at sites around Loughborough may list leveller defects that need attention, and we can price each item directly from the report. When a leveller at a warehouse near Loughborough sinks under load, it should be taken out of use until the hydraulic cause has been found and fixed.
Docks in Loughborough receiving trailers at widely varying bed heights can wear lip hinges faster, and hinge rebuilds are a routine part of leveller repair.
We do not turn up and then name a price. Every repair or service visit in Loughborough is agreed in writing first, including what the charge covers. Sending photos of the damage, error codes or leaks helps us diagnose the problem before travelling and bring the likely parts. Any additional work found on the day is quoted for your approval before it starts. You then get a written report for your records.
What are the most common dock leveller faults?
The most common dock leveller faults are hydraulic leaks, power pack failures, lip and hinge damage, and control faults. The way the leveller behaves usually points to the cause.
- Will not rise, or rises slowly: power pack motor or pump, low oil, a failed contactor or a control fault.
- Sinks under load or drifts down when parked: leaking cylinder seals or a faulty check valve.
- Drops suddenly, then locks: the safety valve doing its job after a hose or fitting failure.
- Lip will not extend or falls short: a lip cylinder fault, a sequence valve problem or a seized lip hinge.
- Oil in the pit: a leaking hose, fitting or cylinder.
- Jerky or noisy movement: air in the hydraulics or worn pivots.
- Cracked deck, bent lip or broken hinge knuckles: impact damage or fatigue.
A leveller showing any of these faults should be taken out of use until it has been checked.
What inspection rules apply to dock levellers?
Dock levellers are work equipment under the Provision and Use of Work Equipment Regulations 1998 (PUWER), so they must be maintained in a safe condition and inspected where deterioration could lead to danger. In Northern Ireland the equivalent is PUWER (Northern Ireland) 1999.
Engineering insurers commonly inspect dock levellers under PUWER at 12-month intervals. Their reports list defects, sometimes marked for action before further use, and repairs are often needed to clear them.
Most levellers are treated as work equipment under PUWER. A leveller designed or used to lift people may fall under the Lifting Operations and Lifting Equipment Regulations (LOLER), with 6-monthly thorough examination. This depends on the equipment and how it is used; your insurer or competent person will confirm.
Levellers are made to BS EN 1398:2009, the dock leveller safety standard. HSE guidance notes that guards or skirting may be needed where something could be caught, so damaged toe guards are repaired as part of the job. See our guide to dock leveller inspections under PUWER and LOLER.
The visit price is agreed before anyone attends. Parts and any extra work are quoted before they are fitted.
What we look at around the bay
- Safety edges, photocells and light curtains
- Control panels, push buttons and emergency stops
- Previous service and inspection records, where available
- Door springs, cables and drums for wear or damage
- Vehicle restraint engagement and its signal sequence
- Dock bumpers for missing rubber or loose fixings
Options to discuss
Hydraulic repairs
Cylinders resealed or replaced, hoses and fittings renewed, check and safety valves tested, and the system refilled with fresh oil and bled so the platform moves smoothly again.
Control and safety repairs
Control panels, push buttons, limit switches, maintenance struts, toe guards and side skirts repaired or replaced so the leveller operates and parks safely.
Planning, building control and safety law in England
Sites in Loughborough fall under the rules for England. Structural changes such as forming a new opening or a dock leveller pit may need Building Regulations approval, and external structures such as loading houses, canopies or new dock approaches can need planning permission from the local planning authority. We check what applies before any work starts and build any approvals into the plan.
Questions about dock leveller repairs in Loughborough
Do you cover Leicestershire for dock leveller repairs?
Yes. We take on dock leveller repairs for sites in Loughborough and throughout Leicestershire. Each visit is arranged in advance, with the price agreed in writing before anyone attends. Specialist service engineers working under our management carry out the work, and we remain your point of contact from the first call to the written report.
What information helps before a repair visit?
Photos or a short video of the fault are the most useful thing you can send, along with the make and model from the data plate, a description of what happens when the equipment is operated and any error codes. For a site in Loughborough, also tell us about access, parking and site rules. With that, we can price the visit and bring the likely parts.
How often should equipment at our Loughborough site be serviced?
It depends on how hard the equipment works and on the manufacturer's recommendations. A multi-shift dock with frequent trailer movements needs more attention than a door that opens a few times a day. We suggest a schedule after looking at the equipment and how it is used, and we can line visits up with your insurance inspections where that helps.
Can a leveller be repaired without disturbing the pit?
Usually yes. Most leveller repairs are carried out in place, working from the deck or from the pit with the platform propped. If the pit itself is cracked, broken at the edges or holding water, that is noted in the report and any pit repair is priced separately.
Do you repair mechanical dock levellers?
Yes, where parts are still available. Mechanical levellers use springs and a hold-down mechanism rather than hydraulics, and common repairs include springs, release mechanisms and lip hinges. Where parts are hard to find or faults keep recurring, the report may suggest pricing a hydraulic replacement.
Dock leveller repairs near Loughborough
Nearby places we cover, measured from Loughborough, include Mountsorrel (4 miles), Coalville (8 miles) and Castle Donington (8 miles). Ask if your own town is missing.
Other loading bay services in Loughborough
Full guide to dock leveller repairs · Everything we do in Loughborough
Call us or request a quote online to talk through loading bay work at your site in Loughborough.