- Location
- Gosport, Hampshire
- Main postcode district
- PO12
- Nearby (straight line)
- Portsmouth (2 miles), Fareham (4 miles) and Ryde (5 miles)
- Visit pricing
- Agreed in writing before we attend
Dock leveller repair covers finding and fixing faults on the bridge between the dock and the trailer bed, including hydraulic cylinders, hoses and power packs, safety and check valves, lip hinges and lip cylinders, platform and lip damage, toe guards and control panels. It applies to swing-lip, telescopic-lip, mechanical and edge-of-dock levellers, with the aim of returning each one to safe working order.
How does this suit sites in Gosport?
Landlords and managing agents in Gosport with several units can group leveller repairs into planned visits, keeping access costs down across the estate. Docks in Gosport receiving trailers at widely varying bed heights can wear lip hinges faster, and hinge rebuilds are a routine part of leveller repair.
Low temperatures at chilled and frozen docks in Gosport can affect hydraulic oil and seals, so it helps to mention the operating temperature when reporting a fault.
Our repair process in Gosport has four parts. You describe the problem and send photos. We price the visit and confirm it in writing. The engineer attends, carries out the agreed work and quotes anything additional before doing it. You then receive a written report on the condition of the equipment and the work completed, which is useful for insurers, inspectors and your own planning.
What are the most common dock leveller faults?
The most common dock leveller faults are hydraulic leaks, power pack failures, lip and hinge damage, and control faults. The way the leveller behaves usually points to the cause.
- Will not rise, or rises slowly: power pack motor or pump, low oil, a failed contactor or a control fault.
- Sinks under load or drifts down when parked: leaking cylinder seals or a faulty check valve.
- Drops suddenly, then locks: the safety valve doing its job after a hose or fitting failure.
- Lip will not extend or falls short: a lip cylinder fault, a sequence valve problem or a seized lip hinge.
- Oil in the pit: a leaking hose, fitting or cylinder.
- Jerky or noisy movement: air in the hydraulics or worn pivots.
- Cracked deck, bent lip or broken hinge knuckles: impact damage or fatigue.
A leveller showing any of these faults should be taken out of use until it has been checked.
What inspection rules apply to dock levellers?
Dock levellers are work equipment under the Provision and Use of Work Equipment Regulations 1998 (PUWER), so they must be maintained in a safe condition and inspected where deterioration could lead to danger. In Northern Ireland the equivalent is PUWER (Northern Ireland) 1999.
Engineering insurers commonly inspect dock levellers under PUWER at 12-month intervals. Their reports list defects, sometimes marked for action before further use, and repairs are often needed to clear them.
Most levellers are treated as work equipment under PUWER. A leveller designed or used to lift people may fall under the Lifting Operations and Lifting Equipment Regulations (LOLER), with 6-monthly thorough examination. This depends on the equipment and how it is used; your insurer or competent person will confirm.
Levellers are made to BS EN 1398:2009, the dock leveller safety standard. HSE guidance notes that guards or skirting may be needed where something could be caught, so damaged toe guards are repaired as part of the job. See our guide to dock leveller inspections under PUWER and LOLER.
The visit price is agreed before anyone attends. Parts and any extra work are quoted before they are fitted.
What we look at around the bay
- Control panels, push buttons and emergency stops
- Door springs, cables and drums for wear or damage
- Wiring, isolators and motor performance under load
- Vehicle restraint engagement and its signal sequence
- Safety edges, photocells and light curtains
- Door panels, side seals and bottom rubbers
Options to discuss
Lip and hinge repairs
Seized or worn lip hinges rebuilt, hinge pins replaced, bent lips straightened or replaced, and lip cylinders repaired so the lip extends fully on to the trailer bed.
Control and safety repairs
Control panels, push buttons, limit switches, maintenance struts, toe guards and side skirts repaired or replaced so the leveller operates and parks safely.
Regulations and approvals in England
Lift tables and dock lifts in Gosport may fall under LOLER, with thorough examination at least every 12 months, or every 6 months where people are lifted. It depends on the equipment and how it is used, and your insurer or competent person will confirm. Dock levellers are usually treated as work equipment under PUWER. We check what applies before any work starts.
Questions about dock leveller repairs in Gosport
Do you provide a written report after each visit?
Yes. After every repair or service visit to a site in Gosport, you receive a written report setting out what was checked, what was found, what work was carried out and anything that still needs attention, with a quote for further work where needed. The report is useful for your maintenance records and for discussions with your insurer or inspector.
How is a repair or service visit in Gosport priced?
Repair and service visits are chargeable, and the price is agreed in writing before anyone attends. For dock leveller repairs, the guide budget is £220 to £2,600 per repair, excluding VAT. The exact figure depends on the fault, parts, access and timing. If the engineer finds further work on the day, it is quoted for your approval before it is carried out.
Do you cover Hampshire for dock leveller repairs?
Yes. We take on dock leveller repairs for sites in Gosport and throughout Hampshire. Each visit is arranged in advance, with the price agreed in writing before anyone attends. Specialist service engineers working under our management carry out the work, and we remain your point of contact from the first call to the written report.
Can a leveller be repaired without disturbing the pit?
Usually yes. Most leveller repairs are carried out in place, working from the deck or from the pit with the platform propped. If the pit itself is cracked, broken at the edges or holding water, that is noted in the report and any pit repair is priced separately.
Can leveller repairs be done outside operating hours?
Yes, leveller repairs can be arranged for evenings or weekends where that suits your operation. Out-of-hours working costs more, and that is included in the visit price agreed in writing beforehand. Timing for each repair is agreed with you, and neighbouring bays can usually keep working.
Dock leveller repairs near Gosport
Nearby places we cover, measured from Gosport, include Portsmouth (2 miles), Fareham (4 miles) and Ryde (5 miles). Ask if your own town is missing.
Other loading bay services in Gosport
Full guide to dock leveller repairs · Everything we do in Gosport
Have photos of the door, leveller or shelter? Send them with your enquiry and we can give a clearer answer for your Gosport site.