- Location
- Mangotsfield, Gloucestershire
- Main postcode district
- BS16
- Nearby (straight line)
- Kingswood (2 miles), Bristol (5 miles) and Keynsham (5 miles)
- Visit pricing
- Agreed in writing before we attend
Dock leveller repair covers finding and fixing faults on the bridge between the dock and the trailer bed, including hydraulic cylinders, hoses and power packs, safety and check valves, lip hinges and lip cylinders, platform and lip damage, toe guards and control panels. It applies to swing-lip, telescopic-lip, mechanical and edge-of-dock levellers, with the aim of returning each one to safe working order.
What matters for dock leveller repairs in Mangotsfield?
Every leveller repair enquiry from Mangotsfield starts with you describing the fault, then a visit price agreed in writing before an engineer attends. Low temperatures at chilled and frozen docks in Mangotsfield can affect hydraulic oil and seals, so it helps to mention the operating temperature when reporting a fault.
Insurer inspections at sites around Mangotsfield may list leveller defects that need attention, and we can price each item directly from the report.
Tell us what has gone wrong at your Mangotsfield site and, if you can, send photos of the fault and any labels on the equipment. We then confirm the visit price in writing, and nobody attends until you have agreed it. On site, the engineer diagnoses and repairs what was agreed; anything extra is quoted first, never added without your say-so. A written report follows, covering findings, work carried out and recommendations.
What are the most common dock leveller faults?
The most common dock leveller faults are hydraulic leaks, power pack failures, lip and hinge damage, and control faults. The way the leveller behaves usually points to the cause.
- Will not rise, or rises slowly: power pack motor or pump, low oil, a failed contactor or a control fault.
- Sinks under load or drifts down when parked: leaking cylinder seals or a faulty check valve.
- Drops suddenly, then locks: the safety valve doing its job after a hose or fitting failure.
- Lip will not extend or falls short: a lip cylinder fault, a sequence valve problem or a seized lip hinge.
- Oil in the pit: a leaking hose, fitting or cylinder.
- Jerky or noisy movement: air in the hydraulics or worn pivots.
- Cracked deck, bent lip or broken hinge knuckles: impact damage or fatigue.
A leveller showing any of these faults should be taken out of use until it has been checked.
What inspection rules apply to dock levellers?
Dock levellers are work equipment under the Provision and Use of Work Equipment Regulations 1998 (PUWER), so they must be maintained in a safe condition and inspected where deterioration could lead to danger. In Northern Ireland the equivalent is PUWER (Northern Ireland) 1999.
Engineering insurers commonly inspect dock levellers under PUWER at 12-month intervals. Their reports list defects, sometimes marked for action before further use, and repairs are often needed to clear them.
Most levellers are treated as work equipment under PUWER. A leveller designed or used to lift people may fall under the Lifting Operations and Lifting Equipment Regulations (LOLER), with 6-monthly thorough examination. This depends on the equipment and how it is used; your insurer or competent person will confirm.
Levellers are made to BS EN 1398:2009, the dock leveller safety standard. HSE guidance notes that guards or skirting may be needed where something could be caught, so damaged toe guards are repaired as part of the job. See our guide to dock leveller inspections under PUWER and LOLER.
The visit price is agreed before anyone attends. Parts and any extra work are quoted before they are fitted.
What we look at around the bay
- Lip hinge, lip extension and lip support operation
- Track alignment, rollers and wall fixings
- Safety edges, photocells and light curtains
- Shelter curtains, frames and side pads for tears
- Wiring, isolators and motor performance under load
- Inflatable shelter fans, airbags and control function
Options to discuss
Lip and hinge repairs
Seized or worn lip hinges rebuilt, hinge pins replaced, bent lips straightened or replaced, and lip cylinders repaired so the lip extends fully on to the trailer bed.
Hydraulic repairs
Cylinders resealed or replaced, hoses and fittings renewed, check and safety valves tested, and the system refilled with fresh oil and bled so the platform moves smoothly again.
Which rules apply in England?
Lift tables and dock lifts in Mangotsfield may fall under LOLER, with thorough examination at least every 12 months, or every 6 months where people are lifted. It depends on the equipment and how it is used, and your insurer or competent person will confirm. Dock levellers are usually treated as work equipment under PUWER. We check what applies before any work starts.
Questions about dock leveller repairs in Mangotsfield
What happens if the engineer finds the equipment unsafe?
If equipment is found to be unsafe, the engineer will tell you straight away and recommend that it is isolated and taken out of use until it is repaired. That is recorded in the written report. We then quote the repair so you can decide how to proceed. Keeping an unsafe door or leveller in service puts people at risk, so we will always raise it.
Can you repair all makes of loading bay equipment?
We work on common makes and types of doors, dock levellers, shelters, seals and restraints. Parts availability varies, particularly for older or discontinued equipment, so it helps to send the make, model and photos of any data plates from your site in Mangotsfield. If original parts are not available, we tell you and price the alternatives, including replacement where that makes more sense.
What is the difference between servicing and a statutory inspection?
Servicing keeps equipment working: cleaning, adjusting, lubricating and replacing worn parts. A statutory inspection or thorough examination is a separate check by a competent person, often arranged through your engineering insurer. Dock levellers are commonly inspected under PUWER at 12-month intervals, and lift tables may need LOLER thorough examination, depending on the equipment and how it is used. Your insurer or competent person will confirm what applies.
How is the price for a leveller repair agreed?
You describe the fault and send photos, and we agree the visit price in writing before anyone attends. If the engineer finds more work is needed, it is quoted and only carried out once you approve it. The visit is chargeable, and the price is always agreed first.
Will the repair clear an insurer's defect notice?
A repair addresses the defect listed, and our written report records what was found and what was done, which you can keep with the insurer's report. Whether the insurer needs to re-inspect is between you and them. Any further defects found during the repair are quoted before work.
Dock leveller repairs near Mangotsfield
If your site is not in Mangotsfield itself, it may be near one of these: Kingswood (2 miles), Bristol (5 miles) and Keynsham (5 miles). Pick the closest.
Other loading bay services in Mangotsfield
Full guide to dock leveller repairs · Everything we do in Mangotsfield
Request a quote for your loading bay in Mangotsfield, attaching photos of the dock, the equipment and any damage.