- Location
- Tiverton, Devon
- Main postcode district
- EX16
- Nearby (straight line)
- Exeter (12 miles), Taunton (19 miles) and Exmouth (20 miles)
- Visit pricing
- Agreed in writing before we attend
Dock leveller repair covers finding and fixing faults on the bridge between the dock and the trailer bed, including hydraulic cylinders, hoses and power packs, safety and check valves, lip hinges and lip cylinders, platform and lip damage, toe guards and control panels. It applies to swing-lip, telescopic-lip, mechanical and edge-of-dock levellers, with the aim of returning each one to safe working order.
Where does this fit at a dock in Tiverton?
Distribution docks in Tiverton that run several shifts put heavy cycles through leveller hydraulics, so leaks and slow operation can show up sooner. Docks in Tiverton receiving trailers at widely varying bed heights can wear lip hinges faster, and hinge rebuilds are a routine part of leveller repair.
Every leveller repair enquiry from Tiverton starts with you describing the fault, then a visit price agreed in writing before an engineer attends.
When something stops working at a loading bay in Tiverton, contact us with a description and, ideally, photos. We will confirm the cost of the visit in writing before booking anyone. If the engineer finds the problem goes further than expected, you receive a quote for the additional work and decide whether to proceed. Every visit is followed by a written report you can keep with your maintenance records.
What are the most common dock leveller faults?
The most common dock leveller faults are hydraulic leaks, power pack failures, lip and hinge damage, and control faults. The way the leveller behaves usually points to the cause.
- Will not rise, or rises slowly: power pack motor or pump, low oil, a failed contactor or a control fault.
- Sinks under load or drifts down when parked: leaking cylinder seals or a faulty check valve.
- Drops suddenly, then locks: the safety valve doing its job after a hose or fitting failure.
- Lip will not extend or falls short: a lip cylinder fault, a sequence valve problem or a seized lip hinge.
- Oil in the pit: a leaking hose, fitting or cylinder.
- Jerky or noisy movement: air in the hydraulics or worn pivots.
- Cracked deck, bent lip or broken hinge knuckles: impact damage or fatigue.
A leveller showing any of these faults should be taken out of use until it has been checked.
What inspection rules apply to dock levellers?
Dock levellers are work equipment under the Provision and Use of Work Equipment Regulations 1998 (PUWER), so they must be maintained in a safe condition and inspected where deterioration could lead to danger. In Northern Ireland the equivalent is PUWER (Northern Ireland) 1999.
Engineering insurers commonly inspect dock levellers under PUWER at 12-month intervals. Their reports list defects, sometimes marked for action before further use, and repairs are often needed to clear them.
Most levellers are treated as work equipment under PUWER. A leveller designed or used to lift people may fall under the Lifting Operations and Lifting Equipment Regulations (LOLER), with 6-monthly thorough examination. This depends on the equipment and how it is used; your insurer or competent person will confirm.
Levellers are made to BS EN 1398:2009, the dock leveller safety standard. HSE guidance notes that guards or skirting may be needed where something could be caught, so damaged toe guards are repaired as part of the job. See our guide to dock leveller inspections under PUWER and LOLER.
The visit price is agreed before anyone attends. Parts and any extra work are quoted before they are fitted.
Bay checks on a repair or service visit
- Dock bumpers for missing rubber or loose fixings
- Pit frame welds, platform cracks and structural damage
- Anti-fall device on upward-opening doors
- Inflatable shelter fans, airbags and control function
- Control panels, push buttons and emergency stops
- Manual override and emergency operation on powered doors
Options to discuss
Control and safety repairs
Control panels, push buttons, limit switches, maintenance struts, toe guards and side skirts repaired or replaced so the leveller operates and parks safely.
Structural and weld repairs
Cracked deck plates, broken welds and damaged front sections repaired by welding or with fabricated replacement parts, restoring the platform's strength.
What do the rules in England mean for the work?
Lift tables and dock lifts in Tiverton may fall under LOLER, with thorough examination at least every 12 months, or every 6 months where people are lifted. It depends on the equipment and how it is used, and your insurer or competent person will confirm. Dock levellers are usually treated as work equipment under PUWER. We check what applies before any work starts.
Questions about dock leveller repairs in Tiverton
What information helps before a repair visit?
Photos or a short video of the fault are the most useful thing you can send, along with the make and model from the data plate, a description of what happens when the equipment is operated and any error codes. For a site in Tiverton, also tell us about access, parking and site rules. With that, we can price the visit and bring the likely parts.
What happens if the engineer finds the equipment unsafe?
If equipment is found to be unsafe, the engineer will tell you straight away and recommend that it is isolated and taken out of use until it is repaired. That is recorded in the written report. We then quote the repair so you can decide how to proceed. Keeping an unsafe door or leveller in service puts people at risk, so we will always raise it.
Do you cover Devon for dock leveller repairs?
Yes. We take on dock leveller repairs for sites in Tiverton and throughout Devon. Each visit is arranged in advance, with the price agreed in writing before anyone attends. Specialist service engineers working under our management carry out the work, and we remain your point of contact from the first call to the written report.
Can a leveller be repaired without disturbing the pit?
Usually yes. Most leveller repairs are carried out in place, working from the deck or from the pit with the platform propped. If the pit itself is cracked, broken at the edges or holding water, that is noted in the report and any pit repair is priced separately.
Will the repair clear an insurer's defect notice?
A repair addresses the defect listed, and our written report records what was found and what was done, which you can keep with the insurer's report. Whether the insurer needs to re-inspect is between you and them. Any further defects found during the repair are quoted before work.
Dock leveller repairs near Tiverton
The same survey, quote and repair service is available in towns around Tiverton, such as Exeter (12 miles), Taunton (19 miles) and Exmouth (20 miles).
Other loading bay services in Tiverton
Full guide to dock leveller repairs · Everything we do in Tiverton
Speak to us about your Tiverton loading bay. We will ask the right questions, then set out the next step clearly.