- Location
- Evesham, Worcestershire
- Main postcode district
- WR11
- Nearby (straight line)
- Tewkesbury (11 miles), Stratford-upon-Avon (12 miles) and Worcester (13 miles)
- Survey and quote
- Free, with a fixed written quote
Dock bumpers are rubber or rubber-and-steel buffers fixed to the face of a loading dock, either side of the leveller, to absorb the impact of reversing vehicles. They hold the trailer a set distance from the building, protect the dock wall, leveller and door, and help a dock seal or shelter compress evenly. Most bays use two bumpers, replaced as they wear.
What should sites in Evesham consider?
We survey and quote for dock bumper work in Evesham on the same basis as anywhere else in the UK, with the price fixed in a written quote. When a landlord in Evesham re-lets a unit, replacing tired bumpers is a modest cost that protects the leveller and dock wall for the incoming tenant.
Distribution sheds in Evesham that take trailers on and off the dock all day wear through bumper rubber faster than quieter sites, so it pays to check them at every service.
We keep the process simple for sites in Evesham. A free survey tells us what the dock needs; a fixed written quote tells you what it will cost and what is included. We then organise the installation, with specialist engineers under our management and a programme agreed around your shifts. Night and weekend work is available by arrangement. Before we leave, the new equipment is tested, demonstrated and handed over with its documentation.
When should dock bumpers be replaced?
Dock bumpers should be replaced when the rubber is worn close to the steel backing, split, missing layers or loose on its fixings. At that point the bumper no longer stops the trailer before it reaches the dock wall or leveller.
Common signs include:
- Rubber worn into a curve or step where trailer chassis rub against it.
- Laminated layers missing or bowed out between the steel angles.
- Loose bolts, cracked concrete or rust staining around the fixings.
- Uneven compression on a dock seal, showing trailers are sitting off-square.
Replace bumpers in pairs where possible, so the trailer is held square and both sides compress evenly. Steel-faced designs with replaceable faces can often be refreshed by changing the face plate alone, which keeps costs down on very busy bays.
Which dock bumper is best: laminated, moulded or steel-faced?
Laminated rubber bumpers suit most general docks, steel-faced bumpers suit busy bays where trailers rise and fall during loading, and moulded bumpers suit lighter vehicles and compact installations.
- Laminated rubber: layers of fabric-reinforced rubber pressed between steel angles on threaded bars. They absorb impact well, are economical and are the standard choice for many bays.
- Moulded rubber: solid rubber blocks in rectangular or curved profiles. They are neat and quick to fit, and work well for vans, rigid vehicles and lower-impact docks.
- Steel-faced: a rubber body behind a steel plate. As forklifts drive on and off, the trailer bed moves up and down and scrubs the bumper; the steel face takes that wear instead of the rubber.
- Vertical sliding: a face that travels up and down with the trailer, reducing abrasion on very busy bays.
Where a design has replaceable faces, worn plates can be changed without removing the whole bumper. Our guide to choosing dock bumpers and wheel guides covers projection and positioning in more detail.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What does the free survey cover?
- Traffic routes for vehicles and separation of pedestrians
- Condition of any existing leveller pit, kerb angles and pit drainage
- How often each door cycles during a typical shift
- Asbestos register and any other site hazard information
- Working hours, shift patterns and windows for out-of-hours work
- Wheel guide positions and yard markings for reversing vehicles
Options to discuss
Moulded rubber bumpers
Solid moulded rubber blocks in rectangular or curved profiles. Compact and tidy, they suit vans, rigid vehicles and docks with lighter or less frequent traffic.
Laminated rubber bumpers
Layers of fabric-reinforced rubber clamped between steel angles. Economical and good at absorbing impact, they are the standard choice for many general-purpose loading docks.
Which rules apply in England?
Workplace safety in England is regulated by HSE. For a loading bay in Evesham, that means doors meeting regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, equipment maintained under PUWER and suitable safeguards against vehicles driving away too early. We check what applies at survey and design the bay accordingly.
Questions about dock bumpers in Evesham
Do you remove and dispose of the old equipment?
Yes, where it is part of the scope. When we replace doors, levellers, shelters or seals at a site in Evesham, removal and disposal of the old equipment can be included and is itemised in the quote, so it is clear what is covered. If anything should be kept, such as a frame or motor that is still serviceable, we agree that at survey.
How long does installation take at a site in Evesham?
It depends on the equipment, the number of bays, the condition of the dock and whether any building or electrical work is needed. We agree a programme with you after the survey, setting out which bays are out of use and when. Larger jobs are usually phased so that part of the dock stays open, and out-of-hours working can be arranged.
Is the site survey in Evesham free?
Yes. For new installations, replacements, upgrades, conversions and complete bays, the site survey and written quote are free and come with no obligation. The survey lets us measure the openings, check the dock and structure, and understand how the bay is used, so the quote reflects your site. Repair and servicing visits are different: they are chargeable, with the price agreed before anyone attends.
How many dock bumpers does a loading bay need?
Most loading bays need two dock bumpers, one fixed either side of the leveller. Docks receiving a wide mix of vehicles sometimes need taller bumpers or an extra lower pair so every vehicle meets rubber before it meets the wall. We confirm the number and layout at survey.
Do you replace dock bumpers without changing other equipment?
Yes. Bumper replacement is often a standalone job, and we can fit new bumpers to existing docks without touching the door, leveller or shelter. If we notice other wear on site, such as a damaged seal or a struck leveller lip, we note it for you.
Dock bumpers near Evesham
Close neighbours of Evesham with their own pages here: Tewkesbury (11 miles), Stratford-upon-Avon (12 miles) and Worcester (13 miles). Choose one to see coverage details for that town.
Other loading bay services in Evesham
Full guide to dock bumpers · Everything we do in Evesham
Ready to talk about a loading bay in Evesham? Call us, or send the details through the quote form.