- Location
- Maesteg, Mid Glamorgan
- Main postcode district
- CF34
- Nearby (straight line)
- Briton Ferry (7 miles), Neath (7 miles) and Bridgend (8 miles)
- Survey and quote
- Free, with a fixed written quote
Dock bumpers are rubber or rubber-and-steel buffers fixed to the face of a loading dock, either side of the leveller, to absorb the impact of reversing vehicles. They hold the trailer a set distance from the building, protect the dock wall, leveller and door, and help a dock seal or shelter compress evenly. Most bays use two bumpers, replaced as they wear.
How does this suit sites in Maesteg?
Sites near Maesteg handling a mix of articulated trailers, rigid vehicles and vans may need taller bumpers or a second lower pair to protect the dock face. Multi-tenant estates in Maesteg often see new occupants arrive with different fleets, and bumpers set up for one tenant's trailers may not suit the next.
Older industrial units around Maesteg sometimes still have their original bumpers, or none at all, leaving the dock wall and leveller lip to absorb every reversing impact.
How does an installation in Maesteg work? First, a free, no-obligation survey to measure up and understand the operation. Next, a fixed written quote. Then a programme agreed with you, so the work fits around deliveries, with out-of-hours slots if needed. The installation itself is carried out by specialist engineers who answer to us, and it finishes with testing, a walk-through for your staff and a handover pack.
Where should dock bumpers be positioned on the dock face?
Dock bumpers are normally fixed either side of the leveller, at a height that catches the rear of the trailer before anything else touches the building.
- Height: typical UK dock height is around 1,200 mm, but trailer bed heights vary from roughly 900 to 1,600 mm, so bumpers must cover the range of vehicles you receive.
- Projection: bumpers commonly stand about 100 mm proud of the dock face. Too little and trailers hit the wall; too much and a swing lip of about 400 to 500 mm may not reach far enough on to the trailer bed.
- Spacing: bumpers should line up with the trailer chassis and sit clear of the leveller lip.
- Seals and shelters: projection controls how far a dock seal compresses, so it is set with the seal depth in mind.
Pairing bumpers with steel wheel guides helps drivers reverse square, so both bumpers take an equal share of each impact.
When should dock bumpers be replaced?
Dock bumpers should be replaced when the rubber is worn close to the steel backing, split, missing layers or loose on its fixings. At that point the bumper no longer stops the trailer before it reaches the dock wall or leveller.
Common signs include:
- Rubber worn into a curve or step where trailer chassis rub against it.
- Laminated layers missing or bowed out between the steel angles.
- Loose bolts, cracked concrete or rust staining around the fixings.
- Uneven compression on a dock seal, showing trailers are sitting off-square.
Replace bumpers in pairs where possible, so the trailer is held square and both sides compress evenly. Steel-faced designs with replaceable faces can often be refreshed by changing the face plate alone, which keeps costs down on very busy bays.
The same published guide range applies across Wales; access, out-of-hours working and site conditions are confirmed at the free survey.
What we look at on site
- Wind exposure at the dock, which affects door and shelter choice
- Yard gradient and the slope of the approach to the dock
- Forklift and pallet truck loads crossing the leveller platform
- Gaps around trailers where heated or chilled air escapes
- Drainage on recessed or sloping dock approaches
- Asbestos register and any other site hazard information
Options to discuss
Vertical sliding bumpers
A face that rides up and down with the trailer instead of rubbing against it, reducing wear on very high-throughput docks.
Moulded rubber bumpers
Solid moulded rubber blocks in rectangular or curved profiles. Compact and tidy, they suit vans, rigid vehicles and docks with lighter or less frequent traffic.
What do the rules in Wales mean for the work?
Sites in Maesteg follow the rules for Wales. Forming a new opening or dock pit may need Building Regulations approval, and loading houses, canopies or new dock approaches can need planning permission from the local planning authority. We check what applies at survey, so any approvals are understood before the programme is fixed.
Questions about dock bumpers in Maesteg
What details do you need from us to quote for dock bumpers?
To get started, send the site address in Maesteg, the number of bays or openings, approximate sizes, and photos of the dock from inside and outside. Tell us what vehicles you load, what goods you handle and any temperature requirements. Drawings help on new builds. We then arrange the free survey and confirm the details before the written quote is issued.
Can you work alongside our main contractor on a new build in Maesteg?
Yes. For new warehouses and fit-outs, we can supply and install the dock package as part of a wider project, working to the main contractor's programme, site rules and permits. We will need drawings, dock levels and the programme, and we coordinate pit details, power supplies and door openings with the relevant trades before installation begins.
Do you remove and dispose of the old equipment?
Yes, where it is part of the scope. When we replace doors, levellers, shelters or seals at a site in Maesteg, removal and disposal of the old equipment can be included and is itemised in the quote, so it is clear what is covered. If anything should be kept, such as a frame or motor that is still serviceable, we agree that at survey.
How long do dock bumpers last?
There is no fixed lifespan for a dock bumper, because wear depends on how many trailers use the bay, how hard drivers reverse and how much the trailer moves during loading. A quiet dock may keep the same bumpers for many years, while a busy distribution bay can wear through the rubber much sooner. Checking them at each service visit catches wear early.
Do you replace dock bumpers without changing other equipment?
Yes. Bumper replacement is often a standalone job, and we can fit new bumpers to existing docks without touching the door, leveller or shelter. If we notice other wear on site, such as a damaged seal or a struck leveller lip, we note it for you.
Dock bumpers near Maesteg
Looking beyond Maesteg? Our pages for Briton Ferry (7 miles), Neath (7 miles) and Bridgend (8 miles) describe the same loading bay services and how to get in touch.
Other loading bay services in Maesteg
Full guide to dock bumpers · Everything we do in Maesteg
Whether it is a new bay or a fault on an existing one, call us or request a quote for your site in Maesteg.