- Location
- Yateley, Hampshire
- Main postcode district
- GU46
- Nearby (straight line)
- Sandhurst (2 miles), Crowthorne (2 miles) and Camberley (4 miles)
- Survey and quote
- Free, with a fixed written quote
Dock bumpers are rubber or rubber-and-steel buffers fixed to the face of a loading dock, either side of the leveller, to absorb the impact of reversing vehicles. They hold the trailer a set distance from the building, protect the dock wall, leveller and door, and help a dock seal or shelter compress evenly. Most bays use two bumpers, replaced as they wear.
What matters for dock bumpers in Yateley?
Sites near Yateley handling a mix of articulated trailers, rigid vehicles and vans may need taller bumpers or a second lower pair to protect the dock face. When a landlord in Yateley re-lets a unit, replacing tired bumpers is a modest cost that protects the leveller and dock wall for the incoming tenant.
We survey and quote for dock bumper work in Yateley on the same basis as anywhere else in the UK, with the price fixed in a written quote.
Our part of the job in Yateley is to survey, quote and manage; the fitting itself is done by specialist installation engineers working under our management. The survey and the written quote are free. Once the fixed price is accepted, we agree dates that work around your deliveries and shifts, including out-of-hours working where needed. Every installation is tested before handover, and you receive the documentation for each item fitted.
What happens on site when dock bumpers are fitted?
Fitting dock bumpers is a short job carried out from yard level, and only the bay being worked on is taken out of use.
- Isolate the bay: no trailer on the dock, the leveller parked and the door closed, with the yard area in front coned off.
- Remove the old bumpers: worn units and corroded fixings are taken off and the dock face is checked for cracked or spalled concrete.
- Fix the new bumpers: holes are drilled and the bumpers secured with resin or mechanical anchors, or welded to existing steelwork where that gives the better fixing.
- Allow cure time: resin anchors need time to cure before a trailer is reversed on to them, and the engineer will confirm when the bay can reopen.
We ask you to provide a clear bay, safe access to the yard, a named contact on the day and details of any permit-to-work or site induction. If the dock face needs concrete repair first, that is identified at survey and priced in the quote rather than discovered on the day.
Which dock bumper is best: laminated, moulded or steel-faced?
Laminated rubber bumpers suit most general docks, steel-faced bumpers suit busy bays where trailers rise and fall during loading, and moulded bumpers suit lighter vehicles and compact installations.
- Laminated rubber: layers of fabric-reinforced rubber pressed between steel angles on threaded bars. They absorb impact well, are economical and are the standard choice for many bays.
- Moulded rubber: solid rubber blocks in rectangular or curved profiles. They are neat and quick to fit, and work well for vans, rigid vehicles and lower-impact docks.
- Steel-faced: a rubber body behind a steel plate. As forklifts drive on and off, the trailer bed moves up and down and scrubs the bumper; the steel face takes that wear instead of the rubber.
- Vertical sliding: a face that travels up and down with the trailer, reducing abrasion on very busy bays.
Where a design has replaceable faces, worn plates can be changed without removing the whole bumper. Our guide to choosing dock bumpers and wheel guides covers projection and positioning in more detail.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
Survey checklist for your dock
- Power supply at each bay, including three-phase availability
- Clear opening width and height for each door
- Age and condition of the equipment already in place
- Gaps around trailers where heated or chilled air escapes
- Access for deliveries, cranes or lifting equipment during installation
- Control positions, isolators and any existing interlocks
Options to discuss
Steel-faced bumpers
A rubber body behind a steel face plate that resists scuffing as the trailer bed moves during loading. Suited to busy bays with heavy forklift traffic.
Replacement faces and fixings
New face plates, rubber inserts and anchors for existing bumpers where the body and backing are still sound, keeping replacement costs down on worn bays.
Planning, building control and safety law in England
Powered doors and dock equipment installed in England may carry the UKCA or the CE mark, and doors are covered by the product standard BS EN 13241. We hand over the relevant documentation for each item fitted in Yateley. Planning and Building Regulations questions are never assumed either way: we check what applies at survey, so you know before work is booked.
Questions about dock bumpers in Yateley
How long does installation take at a site in Yateley?
It depends on the equipment, the number of bays, the condition of the dock and whether any building or electrical work is needed. We agree a programme with you after the survey, setting out which bays are out of use and when. Larger jobs are usually phased so that part of the dock stays open, and out-of-hours working can be arranged.
Do you cover Yateley for dock bumpers?
Yes. We take on dock bumpers for businesses in Yateley and across Hampshire. We survey the site, provide a fixed written quote and manage the installation, with specialist installation engineers working under our management. Visits are arranged in advance at a time that suits your operation, and the same single contact stays with the job through to handover.
What warranty comes with new loading bay equipment?
New equipment comes with the manufacturer's warranty, which varies by product. Our workmanship terms are set out in writing in the quote for your Yateley site, so you can see what is covered before you commit. Check the warranty terms for any servicing conditions, and we can quote for planned maintenance once the installation is complete.
Are dock bumpers included in a complete bay package?
Yes. When we supply a complete loading bay, dock bumpers are specified alongside the leveller, door and shelter or seal so that projection, height and seal compression all work together. Bumpers can also be ordered with wheel guides and dock lights as part of a smaller safety upgrade on an existing bay.
Do you replace dock bumpers without changing other equipment?
Yes. Bumper replacement is often a standalone job, and we can fit new bumpers to existing docks without touching the door, leveller or shelter. If we notice other wear on site, such as a damaged seal or a struck leveller lip, we note it for you.
Dock bumpers near Yateley
Sites close to Yateley get the same service, including those in Sandhurst (2 miles), Crowthorne (2 miles) and Camberley (4 miles), with every job run the same way.
Other loading bay services in Yateley
Full guide to dock bumpers · Everything we do in Yateley
Send a few photos of the dock and a short description of the problem, and we will come back to you about your Yateley site.