- Location
- Stepney, Greater London
- Main postcode district
- E1
- Nearby (straight line)
- Beckton (4 miles), Harringay (5 miles) and Walthamstow (5 miles)
- Survey and quote
- Free, with a fixed written quote
Dock bumpers are rubber or rubber-and-steel buffers fixed to the face of a loading dock, either side of the leveller, to absorb the impact of reversing vehicles. They hold the trailer a set distance from the building, protect the dock wall, leveller and door, and help a dock seal or shelter compress evenly. Most bays use two bumpers, replaced as they wear.
Where does this fit at a dock in Stepney?
Multi-tenant estates in Stepney often see new occupants arrive with different fleets, and bumpers set up for one tenant's trailers may not suit the next. When a landlord in Stepney re-lets a unit, replacing tired bumpers is a modest cost that protects the leveller and dock wall for the incoming tenant.
Older industrial units around Stepney sometimes still have their original bumpers, or none at all, leaving the dock wall and leveller lip to absorb every reversing impact.
It starts with a free site survey in Stepney, where we measure the openings, check the dock and talk through how the bay is used. You then receive a fixed written quote. Once you accept, we manage the job: specialist installation engineers carry out the work under our management, planned around your deliveries, and out-of-hours working can be arranged. At handover we test everything with you and leave the documentation.
Where should dock bumpers be positioned on the dock face?
Dock bumpers are normally fixed either side of the leveller, at a height that catches the rear of the trailer before anything else touches the building.
- Height: typical UK dock height is around 1,200 mm, but trailer bed heights vary from roughly 900 to 1,600 mm, so bumpers must cover the range of vehicles you receive.
- Projection: bumpers commonly stand about 100 mm proud of the dock face. Too little and trailers hit the wall; too much and a swing lip of about 400 to 500 mm may not reach far enough on to the trailer bed.
- Spacing: bumpers should line up with the trailer chassis and sit clear of the leveller lip.
- Seals and shelters: projection controls how far a dock seal compresses, so it is set with the seal depth in mind.
Pairing bumpers with steel wheel guides helps drivers reverse square, so both bumpers take an equal share of each impact.
How much do dock bumpers cost?
Dock bumpers typically cost £120 to £480 per bumper, supplied and fitted, excluding VAT. Most bays need two, so the cost per dock depends mainly on the type of bumper and how it is fixed.
The main things that move the price are:
- Bumper type: laminated rubber is the most economical; moulded, steel-faced and vertical sliding designs cost more.
- Size and projection: deeper or taller bumpers use more material and heavier fixings.
- Fixing method: anchoring into sound concrete is simpler than welding to steel embeds or repairing a broken dock face first.
- Number of bays: doing several docks in one visit spreads access and travel costs.
- Working hours and location: out-of-hours working and remote or island sites add cost, and any travel cost is shown in the quote.
These are guide budgets. After a free site survey we send a written quote, and that quote is the fixed price. VAT is added at the standard rate.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
Survey checklist for your dock
- Drainage on recessed or sloping dock approaches
- How often each door cycles during a typical shift
- Wall and steel structure for door, shelter and bumper fixings
- Lighting inside trailers and at the dock face
- Access for deliveries, cranes or lifting equipment during installation
- Dock height and the mix of trailers you load
Options to discuss
Steel-faced bumpers
A rubber body behind a steel face plate that resists scuffing as the trailer bed moves during loading. Suited to busy bays with heavy forklift traffic.
Vertical sliding bumpers
A face that rides up and down with the trailer instead of rubbing against it, reducing wear on very high-throughput docks.
What do the rules in England mean for the work?
Workplace safety in England is regulated by HSE. For a loading bay in Stepney, that means doors meeting regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, equipment maintained under PUWER and suitable safeguards against vehicles driving away too early. We check what applies at survey and design the bay accordingly.
Questions about dock bumpers in Stepney
Which building and safety rules apply to a site in Stepney?
It depends on which UK nation the site is in. England and Wales use Building Regulations approval, Scotland uses building warrants and Northern Ireland uses building control approval from the council. Workplace safety is regulated by HSE in Great Britain and HSENI in Northern Ireland, and energy rules differ between nations. For your site in Stepney, we check what applies at survey and design to it.
What details do you need from us to quote for dock bumpers?
To get started, send the site address in Stepney, the number of bays or openings, approximate sizes, and photos of the dock from inside and outside. Tell us what vehicles you load, what goods you handle and any temperature requirements. Drawings help on new builds. We then arrange the free survey and confirm the details before the written quote is issued.
Is VAT included in your guide prices for dock bumpers?
No. Our customers are businesses, so guide prices exclude VAT, which is added at the standard rate. The same guide range applies in Greater London as everywhere else: for dock bumpers, it is £120 to £480 per bumper, excluding VAT. It covers supply and fit for a typical installation. Your fixed written quote after the free survey shows the net price, the VAT and exactly what is included.
How long do dock bumpers last?
There is no fixed lifespan for a dock bumper, because wear depends on how many trailers use the bay, how hard drivers reverse and how much the trailer moves during loading. A quiet dock may keep the same bumpers for many years, while a busy distribution bay can wear through the rubber much sooner. Checking them at each service visit catches wear early.
Do you replace dock bumpers without changing other equipment?
Yes. Bumper replacement is often a standalone job, and we can fit new bumpers to existing docks without touching the door, leveller or shelter. If we notice other wear on site, such as a damaged seal or a struck leveller lip, we note it for you.
Dock bumpers near Stepney
Businesses outside Stepney may find their nearest town in this list: Beckton (4 miles), Harringay (5 miles) and Walthamstow (5 miles). Each page covers doors, docks, repairs and servicing.
Other loading bay services in Stepney
Full guide to dock bumpers · Everything we do in Stepney
Whether it is a new bay or a fault on an existing one, call us or request a quote for your site in Stepney.