- Location
- Mangotsfield, Gloucestershire
- Main postcode district
- BS16
- Nearby (straight line)
- Kingswood (2 miles), Bristol (5 miles) and Keynsham (5 miles)
- Survey and quote
- Free, with a fixed written quote
Dock bumpers are rubber or rubber-and-steel buffers fixed to the face of a loading dock, either side of the leveller, to absorb the impact of reversing vehicles. They hold the trailer a set distance from the building, protect the dock wall, leveller and door, and help a dock seal or shelter compress evenly. Most bays use two bumpers, replaced as they wear.
What matters for dock bumpers in Mangotsfield?
When a landlord in Mangotsfield re-lets a unit, replacing tired bumpers is a modest cost that protects the leveller and dock wall for the incoming tenant. Multi-tenant estates in Mangotsfield often see new occupants arrive with different fleets, and bumpers set up for one tenant's trailers may not suit the next.
Distribution sheds in Mangotsfield that take trailers on and off the dock all day wear through bumper rubber faster than quieter sites, so it pays to check them at every service.
A single contact at Loading Bay Doors handles your project in Mangotsfield from start to finish. The free site survey and fixed written quote come first, with no obligation to proceed. We then book the installation for times that suit the operation, including out of hours by arrangement, and manage the specialist engineers on site. At the end we commission and test the equipment, walk your team through it and provide the documentation.
Do dock bumpers need inspecting under PUWER?
Dock bumpers should be checked whenever the loading bay is serviced, because they protect equipment that the Provision and Use of Work Equipment Regulations 1998 (PUWER) apply to. In Northern Ireland the equivalent is PUWER (Northern Ireland) 1999.
PUWER requires work equipment, including dock levellers, loading bay doors and shelters, to be suitable, maintained in a safe condition and inspected where deterioration could lead to danger. A bumper worn down to its backing lets trailers strike the leveller lip and front plate, which can crack welds, bend hinges and leave a leveller that is no longer safe to drive across.
Engineering insurers commonly inspect dock levellers under PUWER at 12-month intervals. Replacing a worn bumper usually costs far less than repairing the leveller it should have protected.
The health and safety regulator is HSE in Great Britain and HSENI in Northern Ireland. Including bumpers in planned maintenance checks shows the dock is being looked after.
Where should dock bumpers be positioned on the dock face?
Dock bumpers are normally fixed either side of the leveller, at a height that catches the rear of the trailer before anything else touches the building.
- Height: typical UK dock height is around 1,200 mm, but trailer bed heights vary from roughly 900 to 1,600 mm, so bumpers must cover the range of vehicles you receive.
- Projection: bumpers commonly stand about 100 mm proud of the dock face. Too little and trailers hit the wall; too much and a swing lip of about 400 to 500 mm may not reach far enough on to the trailer bed.
- Spacing: bumpers should line up with the trailer chassis and sit clear of the leveller lip.
- Seals and shelters: projection controls how far a dock seal compresses, so it is set with the seal depth in mind.
Pairing bumpers with steel wheel guides helps drivers reverse square, so both bumpers take an equal share of each impact.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
Survey checklist for your dock
- How drivers are prevented from pulling away too early
- Forklift and pallet truck loads crossing the leveller platform
- Yard gradient and the slope of the approach to the dock
- Bumper position and wear or damage on the dock face
- Wind exposure at the dock, which affects door and shelter choice
- Whether planning, building control or a building warrant may be needed
Options to discuss
Moulded rubber bumpers
Solid moulded rubber blocks in rectangular or curved profiles. Compact and tidy, they suit vans, rigid vehicles and docks with lighter or less frequent traffic.
Replacement faces and fixings
New face plates, rubber inserts and anchors for existing bumpers where the body and backing are still sound, keeping replacement costs down on worn bays.
Regulations and approvals in England
Powered doors and dock equipment installed in England may carry the UKCA or the CE mark, and doors are covered by the product standard BS EN 13241. We hand over the relevant documentation for each item fitted in Mangotsfield. Planning and Building Regulations questions are never assumed either way: we check what applies at survey, so you know before work is booked.
Questions about dock bumpers in Mangotsfield
How do you price dock bumpers for a site in Mangotsfield?
Guide budgets for supply and fit are £120 to £480 per bumper, excluding VAT. The figure moves with size, insulation, the operator, electrics, access, any pit or groundworks and out-of-hours working. Where levellers are involved, the guide assumes an existing, sound pit. After the free survey you receive a fixed written quote, and that is the price for the agreed scope.
Do you remove and dispose of the old equipment?
Yes, where it is part of the scope. When we replace doors, levellers, shelters or seals at a site in Mangotsfield, removal and disposal of the old equipment can be included and is itemised in the quote, so it is clear what is covered. If anything should be kept, such as a frame or motor that is still serviceable, we agree that at survey.
What warranty comes with new loading bay equipment?
New equipment comes with the manufacturer's warranty, which varies by product. Our workmanship terms are set out in writing in the quote for your Mangotsfield site, so you can see what is covered before you commit. Check the warranty terms for any servicing conditions, and we can quote for planned maintenance once the installation is complete.
Can dock bumpers be fitted with an edge-of-dock leveller?
Yes. With an edge-of-dock leveller, bumpers are usually fixed to the dock face either side of the unit, or to the leveller's own mounting frame where it is designed for that. Their projection has to suit the short lip so it still reaches on to the trailer bed, which we check at survey.
Can you replace just the face of a dock bumper?
Yes, on bumpers designed with replaceable faces. Steel-faced and some moulded designs let the worn face plate or rubber insert be changed while the backing stays bolted to the dock. Older laminated bumpers usually have to be replaced as a complete unit, which is still a modest cost compared with repairing impact damage to a leveller.
Dock bumpers near Mangotsfield
Sites close to Mangotsfield get the same service, including those in Kingswood (2 miles), Bristol (5 miles) and Keynsham (5 miles), with every job run the same way.
Other loading bay services in Mangotsfield
Full guide to dock bumpers · Everything we do in Mangotsfield
Request a quote for your loading bay in Mangotsfield, attaching photos of the dock, the equipment and any damage.