- Location
- Coleraine, County Londonderry
- Main postcode districts
- BT51 and BT52
- Nearby (straight line)
- Limavady (13 miles), Ballymena (24 miles) and Magherafelt (26 miles)
- Survey and quote
- Free, with a fixed written quote
Dock bumpers are rubber or rubber-and-steel buffers fixed to the face of a loading dock, either side of the leveller, to absorb the impact of reversing vehicles. They hold the trailer a set distance from the building, protect the dock wall, leveller and door, and help a dock seal or shelter compress evenly. Most bays use two bumpers, replaced as they wear.
Where does this fit at a dock in Coleraine?
Chilled and food distribution operations in Coleraine depend on dock seals compressing evenly, which only happens when the bumpers behind them are still the correct depth. For new-build warehouses in Coleraine, bumpers are best specified alongside the leveller and seal so that projection and seal compression are correct before the first trailer arrives.
We survey and quote for dock bumper work in Coleraine on the same basis as anywhere else in the UK, with the price fixed in a written quote.
It starts with a free site survey in Coleraine, where we measure the openings, check the dock and talk through how the bay is used. You then receive a fixed written quote. Once you accept, we manage the job: specialist installation engineers carry out the work under our management, planned around your deliveries, and out-of-hours working can be arranged. At handover we test everything with you and leave the documentation.
Where should dock bumpers be positioned on the dock face?
Dock bumpers are normally fixed either side of the leveller, at a height that catches the rear of the trailer before anything else touches the building.
- Height: typical UK dock height is around 1,200 mm, but trailer bed heights vary from roughly 900 to 1,600 mm, so bumpers must cover the range of vehicles you receive.
- Projection: bumpers commonly stand about 100 mm proud of the dock face. Too little and trailers hit the wall; too much and a swing lip of about 400 to 500 mm may not reach far enough on to the trailer bed.
- Spacing: bumpers should line up with the trailer chassis and sit clear of the leveller lip.
- Seals and shelters: projection controls how far a dock seal compresses, so it is set with the seal depth in mind.
Pairing bumpers with steel wheel guides helps drivers reverse square, so both bumpers take an equal share of each impact.
When should dock bumpers be replaced?
Dock bumpers should be replaced when the rubber is worn close to the steel backing, split, missing layers or loose on its fixings. At that point the bumper no longer stops the trailer before it reaches the dock wall or leveller.
Common signs include:
- Rubber worn into a curve or step where trailer chassis rub against it.
- Laminated layers missing or bowed out between the steel angles.
- Loose bolts, cracked concrete or rust staining around the fixings.
- Uneven compression on a dock seal, showing trailers are sitting off-square.
Replace bumpers in pairs where possible, so the trailer is held square and both sides compress evenly. Steel-faced designs with replaceable faces can often be refreshed by changing the face plate alone, which keeps costs down on very busy bays.
The same published guide range applies across Northern Ireland; access, out-of-hours working and site conditions are confirmed at the free survey.
Survey checklist for your dock
- Temperature requirements for chilled, frozen or ambient goods
- Clear opening width and height for each door
- Traffic routes for vehicles and separation of pedestrians
- Age and condition of the equipment already in place
- Dock height and the mix of trailers you load
- Wheel guide positions and yard markings for reversing vehicles
Options to discuss
Replacement faces and fixings
New face plates, rubber inserts and anchors for existing bumpers where the body and backing are still sound, keeping replacement costs down on worn bays.
Steel-faced bumpers
A rubber body behind a steel face plate that resists scuffing as the trailer bed moves during loading. Suited to busy bays with heavy forklift traffic.
Planning, building control and safety law in Northern Ireland
Northern Ireland has its own system. Structural alterations at a site in Coleraine, such as a new opening or dock pit, may need building control approval from the council, and external structures such as loading houses or canopies can need planning permission through the council planning service. We check what applies at survey.
Questions about dock bumpers in Coleraine
How long does installation take at a site in Coleraine?
It depends on the equipment, the number of bays, the condition of the dock and whether any building or electrical work is needed. We agree a programme with you after the survey, setting out which bays are out of use and when. Larger jobs are usually phased so that part of the dock stays open, and out-of-hours working can be arranged.
Do you cover Coleraine for dock bumpers?
Yes. We take on dock bumpers for businesses in Coleraine and across County Londonderry. We survey the site, provide a fixed written quote and manage the installation, with specialist installation engineers working under our management. Visits are arranged in advance at a time that suits your operation, and the same single contact stays with the job through to handover.
How do you price dock bumpers for a site in Coleraine?
Guide budgets for supply and fit are £120 to £480 per bumper, excluding VAT. The figure moves with size, insulation, the operator, electrics, access, any pit or groundworks and out-of-hours working. Where levellers are involved, the guide assumes an existing, sound pit. After the free survey you receive a fixed written quote, and that is the price for the agreed scope.
How long do dock bumpers last?
There is no fixed lifespan for a dock bumper, because wear depends on how many trailers use the bay, how hard drivers reverse and how much the trailer moves during loading. A quiet dock may keep the same bumpers for many years, while a busy distribution bay can wear through the rubber much sooner. Checking them at each service visit catches wear early.
How many dock bumpers does a loading bay need?
Most loading bays need two dock bumpers, one fixed either side of the leveller. Docks receiving a wide mix of vehicles sometimes need taller bumpers or an extra lower pair so every vehicle meets rubber before it meets the wall. We confirm the number and layout at survey.
Dock bumpers near Coleraine
Sites close to Coleraine get the same service, including those in Limavady (13 miles), Ballymena (24 miles) and Magherafelt (26 miles), with every job run the same way.
Other loading bay services in Coleraine
Full guide to dock bumpers · Everything we do in Coleraine
Speak to us about your Coleraine loading bay. We will ask the right questions, then set out the next step clearly.