- Location
- Fraserburgh, Aberdeen and Aberdeenshire
- Main postcode district
- AB43
- Nearby (straight line)
- Peterhead (15 miles)
- Survey and quote
- Free, with a fixed written quote
Dock bumpers are rubber or rubber-and-steel buffers fixed to the face of a loading dock, either side of the leveller, to absorb the impact of reversing vehicles. They hold the trailer a set distance from the building, protect the dock wall, leveller and door, and help a dock seal or shelter compress evenly. Most bays use two bumpers, replaced as they wear.
Why do sites in Fraserburgh choose this?
Older industrial units around Fraserburgh sometimes still have their original bumpers, or none at all, leaving the dock wall and leveller lip to absorb every reversing impact. We survey and quote for dock bumper work in Fraserburgh on the same basis as anywhere else in the UK, with the price fixed in a written quote.
Sites near Fraserburgh handling a mix of articulated trailers, rigid vehicles and vans may need taller bumpers or a second lower pair to protect the dock face.
Your loading bay stays our responsibility from the survey to the handover. In Fraserburgh, the survey and written quote are free, and the quoted price is fixed for the agreed scope. Installation is carried out by specialist engineers working under our management, at times planned with you to protect your loading schedule. Out-of-hours work is available by arrangement. We finish by testing the equipment and handing over its documentation.
How much do dock bumpers cost?
Dock bumpers typically cost £120 to £480 per bumper, supplied and fitted, excluding VAT. Most bays need two, so the cost per dock depends mainly on the type of bumper and how it is fixed.
The main things that move the price are:
- Bumper type: laminated rubber is the most economical; moulded, steel-faced and vertical sliding designs cost more.
- Size and projection: deeper or taller bumpers use more material and heavier fixings.
- Fixing method: anchoring into sound concrete is simpler than welding to steel embeds or repairing a broken dock face first.
- Number of bays: doing several docks in one visit spreads access and travel costs.
- Working hours and location: out-of-hours working and remote or island sites add cost, and any travel cost is shown in the quote.
These are guide budgets. After a free site survey we send a written quote, and that quote is the fixed price. VAT is added at the standard rate.
What happens on site when dock bumpers are fitted?
Fitting dock bumpers is a short job carried out from yard level, and only the bay being worked on is taken out of use.
- Isolate the bay: no trailer on the dock, the leveller parked and the door closed, with the yard area in front coned off.
- Remove the old bumpers: worn units and corroded fixings are taken off and the dock face is checked for cracked or spalled concrete.
- Fix the new bumpers: holes are drilled and the bumpers secured with resin or mechanical anchors, or welded to existing steelwork where that gives the better fixing.
- Allow cure time: resin anchors need time to cure before a trailer is reversed on to them, and the engineer will confirm when the bay can reopen.
We ask you to provide a clear bay, safe access to the yard, a named contact on the day and details of any permit-to-work or site induction. If the dock face needs concrete repair first, that is identified at survey and priced in the quote rather than discovered on the day.
The same published guide range applies across Scotland; access, out-of-hours working and site conditions are confirmed at the free survey.
What we look at on site
- Yard gradient and the slope of the approach to the dock
- Whether planning, building control or a building warrant may be needed
- Gaps around trailers where heated or chilled air escapes
- Headroom above the opening and which track type will suit it
- How drivers are prevented from pulling away too early
- Scope to convert ground-level doors into docks or add lift tables
Options to discuss
Laminated rubber bumpers
Layers of fabric-reinforced rubber clamped between steel angles. Economical and good at absorbing impact, they are the standard choice for many general-purpose loading docks.
Moulded rubber bumpers
Solid moulded rubber blocks in rectangular or curved profiles. Compact and tidy, they suit vans, rigid vehicles and docks with lighter or less frequent traffic.
Which rules apply in Scotland?
Doors and dock equipment installed in Scotland may carry the UKCA or the CE mark, and we pass on the documentation for everything fitted in Fraserburgh. Because building warrant and planning questions can affect the programme, we check what applies at survey and raise any approvals early rather than assuming none are needed.
Questions about dock bumpers in Fraserburgh
Will you deal with building control and planning for a project in Fraserburgh?
We check at survey whether the work is likely to need approval. Forming a new opening or dock pit may need Building Regulations approval, a building warrant or building control approval, depending on the nation, and external structures such as loading houses can need planning permission. Where approval is needed, we explain what is involved, work with your designer or agent, and build it into the programme.
Can you work alongside our main contractor on a new build in Fraserburgh?
Yes. For new warehouses and fit-outs, we can supply and install the dock package as part of a wider project, working to the main contractor's programme, site rules and permits. We will need drawings, dock levels and the programme, and we coordinate pit details, power supplies and door openings with the relevant trades before installation begins.
Which building and safety rules apply to a site in Fraserburgh?
It depends on which UK nation the site is in. England and Wales use Building Regulations approval, Scotland uses building warrants and Northern Ireland uses building control approval from the council. Workplace safety is regulated by HSE in Great Britain and HSENI in Northern Ireland, and energy rules differ between nations. For your site in Fraserburgh, we check what applies at survey and design to it.
Do you replace dock bumpers without changing other equipment?
Yes. Bumper replacement is often a standalone job, and we can fit new bumpers to existing docks without touching the door, leveller or shelter. If we notice other wear on site, such as a damaged seal or a struck leveller lip, we note it for you.
Are dock bumpers included in a complete bay package?
Yes. When we supply a complete loading bay, dock bumpers are specified alongside the leveller, door and shelter or seal so that projection, height and seal compression all work together. Bumpers can also be ordered with wheel guides and dock lights as part of a smaller safety upgrade on an existing bay.
Dock bumpers near Fraserburgh
Distances are measured from Fraserburgh. Nearby towns we cover include Peterhead (15 miles), and other towns in the area are covered too.
Other loading bay services in Fraserburgh
Full guide to dock bumpers · Everything we do in Fraserburgh
Call us or request a quote online to talk through loading bay work at your site in Fraserburgh.