A cold store dock door is an insulated loading bay door built for chilled or frozen buildings, usually a sectional door with thick insulated panels or a high-speed door with an insulated curtain. It differs from a standard dock door in its thermal breaks, extra seals and, on freezer docks, heating in the frame or seals so that ice cannot lock the door shut or tear the seals.
Why do sites in Herefordshire choose this?
During warm, humid spells, any cold store dock in Herefordshire is most exposed to condensation and ice, which is why heated frames and good shelters are worth considering. For a packhouse in Herefordshire handling fresh produce, a well-sealed chilled dock door helps keep warm air out of the store once produce has been cooled.
A chilled distribution centre in Herefordshire opens its dock doors many times a shift, so the door specification matters far more than at an ambient bay.
Here is what happens after you contact us about a site in Herefordshire. We arrange a free survey, measure up and send a fixed written quote. If you go ahead, we manage the whole job, including ordering, delivery and coordination with your site team. Specialist installation engineers working under our management do the fitting, at times built around your loading schedule, with out-of-hours work by arrangement. Testing and handover documents close the job.
How does a cold store door work with the shelter and leveller?
On a cold store dock the door, shelter and leveller should work as one system, with the door opening only once the trailer is sealed against the building and closing before the seal is released.
A typical sequence is:
- The trailer reverses onto the bumpers and is held by a restraint, or the driver's keys are taken.
- The shelter inflates or the seal compresses around the trailer.
- The door opens and the leveller lip is lowered onto the trailer bed.
- Loading takes place inside a sealed link between store and trailer.
- The leveller is stored, the door closes, then the shelter releases.
Interlocks make this sequence automatic, so the door cannot be left open with no trailer present. Insulated leveller platforms and seals around the pit also reduce cold loss through the floor of the bay.
How should a door be specified for a chilled dock compared with a freezer dock?
A chilled dock needs a well-insulated, well-sealed door, while a freezer dock also needs heating to stop ice forming in the frame and seals. The temperature difference across the door drives most specification choices.
- Chilled docks: an insulated sectional door at the thicker end of the common 40 to 80 mm panel range, good perimeter seals and a shelter or seal outside usually do the job.
- Freezer docks: thick panels, thermal breaks in the panel joints, heated side frames and a heated bottom seal, plus a fast operator to cut open time.
- Doors between zones: an insulated high-speed door often suits openings between a chilled marshalling area and a freezer, where traffic is constant.
- Vision panels: possible, but they reduce insulation and can mist, so many freezer docks leave them out.
A cold store door is only as good as the seal around the trailer, which is why we specify the door, shelter and leveller together.
Towns we cover in Herefordshire
We cover cold store dock doors throughout Herefordshire, and the towns below each have their own page. If yours is not listed, get in touch anyway.
Budget range for supply and fit. The written quote after a free survey is the fixed price. All guide prices.
Planning, building control and safety law in England
In England, Approved Document L (2021) sets a limiting U-value of 1.3 W/m²K for vehicle access and similar large doors in new and replacement work. That shapes door specification for sites in Herefordshire, so we confirm the requirement for your project and check what applies at survey before recommending a door.
Questions
Will you deal with building control and planning for a project in Herefordshire?
We check at survey whether the work is likely to need approval. Forming a new opening or dock pit may need Building Regulations approval, a building warrant or building control approval, depending on the nation, and external structures such as loading houses can need planning permission. Where approval is needed, we explain what is involved, work with your designer or agent, and build it into the programme.
How long does installation take at a site in Herefordshire?
It depends on the equipment, the number of bays, the condition of the dock and whether any building or electrical work is needed. We agree a programme with you after the survey, setting out which bays are out of use and when. Larger jobs are usually phased so that part of the dock stays open, and out-of-hours working can be arranged.
What happens to a cold store door in a power cut?
In a power cut the door stops where it is and the frame heating switches off, so it must be possible to operate the door by hand. Powered dock doors normally have a hand chain, crank or release for this. We show your team how to use it at handover so the store can be closed up quickly.
Can a standard sectional door be used on a chilled dock?
A standard insulated sectional door can work on a chilled dock if its panels are thick enough and its seals are in good condition. For frozen docks it is not usually suitable, because it lacks the thermal breaks and frame heating needed to stop ice forming. We advise on the right specification after surveying the store.
Other services in Herefordshire
Full guide to cold store dock doors · All loading bay services in Herefordshire